User manual SAMSUNG SH-09AI8V/SER

[. . . ] Indoor Unit SH09AI8R SH09AI8V Outdoor Unit SH09AI8RX SH09AI8VX E S F I P D G DB98-16808(1) EHNIKA DEUTSCH Split-type Room Air Conditioner (Cool and Heat) Aire acondicionado domstico sistema Split (Refrigeracin y Calefaccin) Climatiseur de type Spar (Refroidissement et Chauffage) Condizionatore d'aria per ambienti ad unit Separate (Raffreddamento e Riscaldamento) Aparelho de ar condicionado tipo Split (Refrigerao e Aquecimento) Geteilte raumklimaanlage (Khlen und Wrmen) IAIPOYMENO KIMATITMTIKO MATIOY (~ η ̷~) PORTUGUS ITALIANO FRANAIS ESPAOL OWNER'S INSTRUCTIONS MANUAL DE INSTRUCCIONES MANUEL D'UTILISATION ISTRUZIONI PER L'USO MANUAL DE INSTRUES GEBRAUCHSANWEISUNG TM TM ENGLISH Safety Precautions The following safety precautions must be taken when using your air conditioner. Disconnect all remote electric power supplies before servicing, installing or cleaning. This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. Users of this product are cautioned not to attempt repair of this product at their own discretion. [. . . ] The air conditioner starts up in the mode selected when the unit was last used. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped lt will start up normally after three minutes. button. IMPORTANT 2 Select COOL mode by pressing the Note You can select the Energy Saving mode only in COOL mode. 3 Press the Result: button. The air conditioner runs in the Energy Saving mode. The outer air flow blade moves up and down. To stop the Energy saving mode, press the button again. 4 To adjust the temperature, press the button one or more times until the required temperature is displayed. Possible temperatures are between 26C and 30C inclusive. Note If you want to adjust temperature under 26C, cancel the Energy Saving mode before adjusting the temperature. 5 To select the fan speed, press the until the required setting is displayed. button one or more times 6 To control the direction of the air flow, refer to page 17. E-15 Generating Anion The air conditioner can generate anion with an ionizer in the indoor unit. Since it is an additional function, you can select it any mode, even when the air conditioner is turned off. Note If you press the button during off, the air conditioner will turn on automatically and generate anion in the Fan mode with Low fan speed. 2 If you wish to stop the Anion function, press the button again. Result: The air conditioner is reset automatically to the previous mode, temperature and fan settings. 3 To control the direction of the air flow, refer to page 17. E-16 Adjusting the Air Flow Direction ENGLISH Depending on the position of the indoor unit on the wall of your room, you can adjust the position of the outer air flow blade on the bottom, left and right of the unit, thus increasing the efficiency of the air conditioner. 1 Press the Result: button one or more times as required. The outer blade is adjusted in the three directions. Cooling Heating Adjust the blade to face. . . Downwards. RECOMMENDATION 2 If you want the blade to move automatically when the air conditioner is operating, press the Result: button. The blade move up and down, left and right, around the base position set. 3 To stop the blade from moving up and down, left and right, press the button again. Note If you switch the air conditioner. . . Set to the initial position powered. Note When you press the button, every blade moves in AUTO/COOL/DRY/FAN/HEAT mode. However, the left and right blades do not move in TURBO mode, and the bottom blade does not move in Sleep mode. E-17 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time. You can set the period of time from 30 minutes to 24 hours. 1 To set the operating time, press the button one or more times until the required time is displayed. Possible time is between 0. 5 hour and 24 hours inclusive. 2 Press the Result: (Set/Cancel) button to complete the setting. The selected mode and the temperature on the display disappear after 10 seconds. [. . . ] Problem The air conditioner does not operate at all Explanation/Solution Check that the breaker used for the air conditioner is switched on. Check that the operation indicator on the indoor unit is on; if necessary press the (On/Off) button on the remote control. Check whether the Timer indicator on the indoor unit is switched on. If so: - Wait until the switch-on time is reached and the air conditioner starts up automatically - Cancel the Timer (see pages 18 and 19 for further details) Check that there are no obstacles between you and the indoor unit. [. . . ]