User manual SAMSUNG SH-09AWHD

[. . . ] Indoor unit SH09AWH SH09ZWH SH12AWH SH12ZWH Outdoor unit SH09AWHX SH09ZWHX SH12AWHX SH12ZWHX IAIPOYMENO KIMATITMTIKO MATIOY (~ η ̷~) EHNIKA E S F I P D G DB98-15083A(3) DEUTSCH Split-type Room Air Conditioner (Cool and Heat) Aire acondicionado domstico sistema Split (Refrigeracin y Calefaccin) Climatiseur de type Spar (Refroidissement et Chauffage) Condizionatore d'aria per ambienti ad unit Separate (Raffreddamento e Riscaldamento) Aparelho de ar condicionado tipo Split (Refrigerao e Aquecimento) Geteilte raumklimaanlage (Khlen und Wrmen) PORTUGUS ITALIANO FRANAIS ESPAOL OWNER'S INSTRUCTIONS MANUAL DE INSTRUCCIONES MANUEL D'UTILISATION ISTRUZIONI PER L'USO MANUAL DE INSTRUES GEBRAUCHSANWEISUNG TM TM ENGLISH Safety Precautions The following safety precautions must be taken when using your air conditioner. Disconnect all remote electric power supplies before servicing, installing or cleaning. This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. Users of this product are cautioned not to attempt repair of this product at their own discretion. [. . . ] You can select the Turbo function in the Auto, Cool and Heat mode. If you select this function in the Dry or Fan mode, it will return to the Auto mode. 3 If you wish to stop the Turbo function before the end of the 30-minute period, press the button one or more times until disappears. Result: The air conditioner is reset automatically to the previous mode, temperature and fan settings. 4 To control the direction of the air flow, refer to pages 16 and 17. E-14 Selecting Energy Saving Mode ENGLISH You can save energy even during operation in the Cool and Heat mode. In the Cool mode, the temperature will rise and in the Heat mode, the temperature will fall, resulting in saving energy. 1 If necessary, press the Result: button. The operation indicator on the indoor unit lights up. The air conditioner starts up in the mode selected when the unit was last used. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped lt will start up normally after three minutes. IMPORTANT 2 Press the Result: button. The air conditioner runs in the Energy saving mode. The outer air flow blade moves up and down. To stop the Energy saving mode, press the again. Note You can select the Energy saving mode in the Cool and Heat mode. 3 To adjust the temperature, press the button one or more times until the required temperature is displayed. 4 To select the fan speed, press the the required setting is displayed. button one or more times until 5 To control the direction of the air flow, refer to pages 16 and 17. E-15 Adjusting the Air Flow Direction Vertically Depending on the position of the indoor unit on the wall of your room, you can adjust the position of the outer air flow blade on the bottom of the unit, thus increasing the efficiency of the air conditioner. 1 Press the Result: button one or more times as required. The outer blade is adjusted vertically. 2 If you want the blade to move up and down automatically when the air conditioner is operating, press the button. Result: The blade move up and down, around the base position set. 3 To stop the blade moving up and down, press the button again. Note If you switch the air conditioner. . . Set to the initial position powered. E-16 Adjusting the Air Flow Direction Horizontally ENGLISH There are two sets of inner air flow blades. Just as the outer air flow blade can be adjusted vertically, the inner blades can be adjusted horizontally. 1 Adjust each set of inner blades to the required position, by pushing or pulling them sideways. E-17 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time. You can set the period of time from 1 hour to 24 hours. 1 To set the operating time, press the button one or more times until the required time is displayed. Possible time is between 1 hour and 24 hour inclusive. 2 Press the Result: button to complete the setting. The selected mode and the temperature on the display disappear after 10 seconds. The air conditioner will switch on automatically when the counter displayed on the remote control reaches the set time and disappears the On Timer setting. 3 To select an operating mode in advance, press the button until the desired mode is displayed at the top of the remote control. Result: The air conditioner will run in the selected mode when it is turned on. Note If you don't operate the remote control after setting the On Timer, it will be turned off automatically after 25 hours. To Cancel the On Timer If you no longer wish to use the On Timer that you have set, you can cancel it at any time. [. . . ] Check that you are pointing the remote control at the remote control sensor in the right of the indoor unit. Replace the remote control batteries if necessary. Check that the correct operating mode has been selected (Auto, Cool, Heat). The room temperature may be too low or too high. [. . . ]