User manual SAMSUNG SH-18ZP0D/XFO

[. . . ] Indoor unit AQ07P2GED AQ18P0GBD SH07APGD AQ18P0GED SH07ZP2D SH18AP0D AQ09P2GBD SH18ZP0D AQ09P2GED AQ24P6GBD SH09APGD AQ24P6GED SH09ZP2D SH24AP6D AQ12P4GBD SH24ZP6D AQ12P4GED SH12APGD SH12ZP4D Outdoor unit UQ07P2GED SH07APGDX SH07ZP2DX UQ09P2GBD UQ09P2GED SH09APGDX SH09ZP2DX UQ12P4GBD UQ12P4GED SH12APGDX SH12ZP4DX UQ18P0GBD UQ18P0GED SH18AP0DX SH18ZP0DX UQ24P6GBD UQ24P6GED SH24AP6DX SH24ZP6DX Split-type Room Air Conditioner (Cool and Heat) Aire acondicionado domstico sistema Split (Refrigeracin y Calefaccin) Climatiseur de type Spar (Refroidissement et Chauffage) Condizionatore d'aria per ambienti ad unit Separate (Raffreddamento e Riscaldamento) Aparelho de ar condicionado tipo Split (Refrigerao e Aquecimento) Geteilte raumklimaanlage (Khlen und Wrmen) IAIPOYMENO KIMATITMTIKO MATIOY (~ η ̷~) E S F I P D G DB98-20924A(2) EHNIKA DEUTSCH PORTUGUS ITALIANO FRANAIS ESPAOL OWNER'S INSTRUCTIONS MANUAL DE INSTRUCCIONES MANUEL D'UTILISATION ISTRUZIONI PER L'USO MANUAL DE INSTRUES GEBRAUCHSANWEISUNG TM TM ENGLISH Register your product at www. samsung. com/global/register Safety Precautions The following safety precautions must be taken when using your air conditioner. Disconnect all remote electric power supplies before servicing, installing or cleaning. This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. x Users of this product are cautioned not to attempt repair of this product at their own discretion. [. . . ] Result: x The indoor unit beeps each time you press the x The air conditioner runs in FAN mode. button. Note 3 Select the fan speed by pressing the until the required setting is displayed: Low Medium High Result: Each time you press the button one or more times button, the indoor unit beeps. 4 To control the direction of the air flow, refer to page 17. E-14 Selecting Energy Saving Mode ENGLISH If you wish to save energy when using your air conditioner, select the Energy saving mode with the Energy saving button. 1 If necessary, press the Result: (On/Off) button. x The operation indicator on the indoor unit lights up. x The air conditioner starts up in the mode selected when the unit was last used. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped lt will start up normally after three minutes. button. IMPORTANT 2 Select COOL mode by pressing the Note You can select the Energy saving mode only in COOL mode. 3 Press the Result: x x x x button. The air conditioner runs in the Energy saving mode. The outer air flow blade moves up and down. To stop the Energy saving mode, press the button again. 4 To adjust the temperature, press the button one or more times until the required temperature is displayed. Possible temperatures are between 26C and 30C inclusive. Note If you want to adjust temperature under 26C, cancel the Energy saving mode before adjusting the temperature. 5 To select the fan speed, press the until the required setting is displayed. button one or more times 6 To control the direction of the air flow, refer to page 17. E-15 Generating Anions The air conditioner can generate anions with an ionizer in the indoor unit. Since it is an additional function, you can select it any mode, even when the air conditioner is turned off. Note If you press the button during off, the air conditioner will turn on automatically and generate anions in the Fan mode with Low fan speed. 2 If you wish to stop the Anions function, press the button again. Result: The air conditioner is reset automatically to the previous mode, temperature and fan settings. 3 To control the direction of the air flow, refer to page 17. E-16 Adjusting the Air Flow Direction Vertically ENGLISH Depending on the position of the indoor unit on the wall of your room, you can adjust the position of the outer air flow blade on the bottom of the unit, thus increasing the efficiency of the air conditioner. 1 Press the Result: button one or more times as required. Cooling Heating Adjust the blade to face. . . Downwards. RECOMMENDATION 2 If you want the blade to move up and down automatically when the air conditioner is operating, press the Result: button. The blade move up and down, around the base position set. 3 To stop the blade moving up and down, press the button again. Note If you switch the air conditioner. . . Set to the initial position powered. Adjusting the Air Flow Direction Horizontally There are two sets of inner air flow blades. Just as the outer air flow blade can be adjusted vertically, the inner blades can be adjusted horizontally. 1 Adjust each set of inner blades to the required position, by pushing or pulling them sideways. E-17 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time. You can set the period of time from 30 minutes to 24 hours. [. . . ] x Check whether the TIMER indicator on the indoor unit is switched on. If so: - Wait until the switch-on time is reached and the air conditioner starts up automatically - Cancel the timer (see pages 18 and 19 for further details) x Check that there are no obstacles between you and the indoor unit. x Check that you are close enough to the indoor unit (seven meters/yards or less). x Check that you are pointing the remote control at the remote control sensor in the right of the indoor unit. [. . . ]