User manual SAMSUNG SH24ZP6B-XSA

[. . . ] Indoor unit AQ07P2GE SH07APG SH07ZP2 AQ09P2GB AQ09P2GE SH09APG SH09ZP2 AQ12P4GB AQ12P4GE SH12APG SH12ZP4 AQ18P0GBA AQ18P0GEA SH18AP0 SH18ZP0B AQ24P6GBA AQ24P6GEA SH24AP6 SH24ZP6B Outdoor unit UQ07P2GE SH07APGX SH07ZP2X UQ09P2GB UQ09P2GE SH09APGX SH09ZP2X UQ12P4GB UQ12P4GE SH12APGX SH12ZP4X UQ18P0GBA UQ18P0GEA SH18AP0X SH18ZP0BX UQ24P6GBA UQ24P6GEA SH24AP6X SH24ZP6BX Split-type Room Air Conditioner (Cool and Heat) Aire acondicionado domstico sistema Split (Refrigeracin y Calefaccin) Climatiseur de type Spar (Refroidissement et Chauffage) Condizionatore d'aria per ambienti ad unit Separate (Raffreddamento e Riscaldamento) Aparelho de ar condicionado tipo Split (Refrigerao e Aquecimento) Geteilte raumklimaanlage (Khlen und Wrmen) IAIPOYMENO KIMATITMTIKO MATIOY (~ η ̷~) E S F I P D G DB98-14758A(3) EHNIKA DEUTSCH PORTUGUS ITALIANO FRANAIS ESPAOL OWNER'S INSTRUCTIONS MANUAL DE INSTRUCCIONES MANUEL D'UTILISATION ISTRUZIONI PER L'USO MANUAL DE INSTRUES GEBRAUCHSANWEISUNG TM TM ENGLISH Safety Precautions The following safety precautions must be taken when using your air conditioner. Disconnect all remote electric power supplies before servicing, installing or cleaning. This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. Users of this product are cautioned not to attempt repair of this product at their own discretion. [. . . ] The air conditioner starts up in the mode selected when the unit was last used. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped lt will start up normally after three minutes. button. IMPORTANT 2 Select COOL mode by pressing the Note You can select the Energy saving mode only in COOL mode. 3 Press the Result: button. The air conditioner runs in the Energy saving mode. The outer air flow blade moves up and down. To stop the Energy saving mode, press the button again. 4 To adjust the temperature, press the button one or more times until the required temperature is displayed. Possible temperatures are between 26C and 30C inclusive. Note If you want to adjust temperature under 26C, cancel the Energy saving mode before adjusting the temperature. 5 To select the fan speed, press the until the required setting is displayed. button one or more times 6 To control the direction of the air flow, refer to page 17. E-15 Generating Anion The air conditioner can generate anion with an ionizer in the indoor unit. Since it is an additional function, you can select it any mode, even when the air conditioner is turned off. Note If you press the button during off, the air conditioner will turn on automatically and generate anion in the Fan mode with Low fan speed. 2 If you wish to stop the Anion function, press the button again. Result: The air conditioner is reset automatically to the previous mode, temperature and fan settings. 3 To control the direction of the air flow, refer to page 17. E-16 Adjusting the Air Flow Direction Vertically ENGLISH Depending on the position of the indoor unit on the wall of your room, you can adjust the position of the outer air flow blade on the bottom of the unit, thus increasing the efficiency of the air conditioner. 1 Press the Result: button one or more times as required. Cooling Heating Adjust the blade to face. . . Downwards. RECOMMENDATION 2 If you want the blade to move up and down automatically when the air conditioner is operating, press the Result: button. The blade move up and down, around the base position set. 3 To stop the blade moving up and down, press the button again. Note If you switch the air conditioner. . . Set to the initial position powered. Adjusting the Air Flow Direction Horizontally There are two sets of inner air flow blades. Just as the outer air flow blade can be adjusted vertically, the inner blades can be adjusted horizontally. 1 Adjust each set of inner blades to the required position, by pushing or pulling them sideways. E-17 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time. You can set the period of time from 30 minutes to 24 hours. 1 To set the operating time, press the button one or more times until the required time is displayed. Possible time is between 0. 5 hour and 24 hour inclusive. 2 Press the Result: (Set/Cancel) button to complete the setting. The selected mode and the temperature on the display disappear after 10 seconds. [. . . ] Check whether the TIMER indicator on the indoor unit is switched on. If so: - Wait until the switch-on time is reached and the air conditioner starts up automatically - Cancel the timer (see pages 18 and 19 for further details) Check that there are no obstacles between you and the indoor unit. Check that you are close enough to the indoor unit (seven meters/yards or less). Check that you are pointing the remote control at the remote control sensor in the right of the indoor unit. [. . . ]