User manual SAMSUNG SHR-3161

[. . . ] User' Manual s ii Digital Video Recorder WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. COMPLIANCE NOTICE OF FCC: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. [. . . ] · Good -- The storage condition is normal. · Bad -- Data cannot be written on or read from the storage device. Inop. -- Storage conditions are normal, however, the S. M. A. R. T. monitoring is not working or supported · S. M. A. R. T. monitoring has detected a fault condition. monitoring has detected that the temperature of storage device exceeded the preset temperature threshold · Not installed -- The storage device is not installed. NOTE: Once the "S. M. A. R. T. Alert" message displays, replacing the hard disk drive is recommended, usually within 24 hours. 25 User' Manual s The °C field displays the temperature of the storage device. The Usage field displays the device usage. NOTE: When the device is an IDE hard disk drive, you can change its usage to either Rec. When the device is a SCSI hard disk drive, you can change its usage to either Extension or Archive. CAUTION: A "­" displays when connecting a hard disk drive that was previously used for something else. In this situation, device usage can be changed as desired usages; e. g. , Extension to Archive or Archive to Extension. However, data on the device will be lost if the device usage is changed. The DVR can be set to react to storage problems by activating an internal buzzer or external alarms, and/or notifying a remote site. Highlight the box beside Storage Problem Action: Alarm Out / Notify and press the button to select from Beep, the alarm output terminal that you want to associate with the storage problem event, and/or Notify. Your DVR shows the condition of the hard disk drives if the installed IDE hard disk drives support the S. M. A. R. T. (Self-Monitoring, Analysis and Reporting Technology) program. Press the button to toggle between On and Off. The Last-check field displays the date and time information of the last storage check. Highlight the box beside Period, and select from Daily, Weekly or Monthly for the check interval. 26 Digital Video Recorder NOTE: When selecting Weekly or Monthly, the Day of Week or Day of Month field will display under the Period field. Select the check day or date. Highlight the box beside Check Time, and adjust the numbers using arrow buttons. Highlight the box beside Temperature Threshold and adjust the numbers using arrow buttons. Set the temperature number to the hard disk drive manufacturer's specifications. If this temperature is ever exceeded, the S. M. A. R. T. [. . . ] If the correct time and date is earlier than the last recorded image, any video with a later time and date will be lost when resetting the correct time and date. No Live Video Live Video Very Bright DVR has stopped recording DVR displays an error message stating that the last recorded image date and time is later than the current date and time setting of the DVR. 81 User' Manual s Appendix D -- Connector Pin Outs Alarm I/O Connector and RS485 Connector Pin Outs Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 Pin Assignment RS485 RX-/TXAlarm Output 3 Alarm Output 1 Alarm Reset Alarm Input 16 Alarm Input 14 Alarm Input 12 Alarm Input 10 Ground Alarm Input 7 Alarm Input 5 Alarm Input 3 Alarm Input 1 Pin Number 14 15 16 17 18 19 20 21 22 23 24 25 Pin Assignment RS485 RX+/TX+ Alarm Output 2 Alarm Output 4 Ground Alarm Input 15 Alarm Input 13 Alarm Input 11 Alarm Input 9 Alarm Input 8 Alarm Input 6 Alarm Input 4 Alarm Input 2 82 Digital Video Recorder Appendix E -- Hard Disk Drive Addition and Replacement Hard Disk Drive Addition 1. Add the hard Slave hard disk drive. NOTE: When the hard disk drive you are adding is a used one, format it on Windows-based PC first. 3. Turn on the unit again. Hard Disk Drive Removal 1. Turn on the unit again. Hard Disk Drive Replacement Case I: When replacing problem ` MASTER'hard disk drives. . . 1. Prepare a new primary IDE hard disk drive. [. . . ]