User manual SAMSUNG SL-M2885FW

[. . . ] User’s Guide BASIC BASIC This guide provides information concerning installation, basic operation and troubleshooting on Windows. M267x series M287x series M288x series ADVANCED This guide provides information about installation, advanced configuration, operation and troubleshooting on various OS environments. Some features may not be available depending on models or countries. BASIC 1. Introduction Key benefits Features by model Useful to know About this user’s guide Safety information Machine overview Control panel overview Turning on the machine Installing the driver locally Reinstalling the driver 5 7 13 14 15 20 23 26 27 29 3. Maintenance Ordering supplies and accessories Available supplies Available maintenance parts Storing the toner cartridge Redistributing toner Replacing the toner cartridge Replacing the imaging unit Monitoring the supplies life Setting the toner low alert Cleaning the machine Tips for moving & storing your machine 69 70 71 72 74 77 80 82 83 84 91 2. [. . . ] Likewise, if the computer’s network configuration is set to Static, the wireless network setting should also be Static. If your computer is set to DHCP and you want to use Static wireless network setting, you must contact the network administrator to get the static IP address. • For the DHCP method If the IP address assignment method is DHCP, check if DHCP is shown in the Wireless Network Setting Confirm window. If it shows Static, click Change TCP/IP to change the assignment method to Receive IP address automatically (DHCP). • For the Static method If the IP address assignment method is Static, check if Static is shown in the Wireless Network Setting Confirm window. If it shows DHCP, click Change TCP/IP to enter the IP address and other network configuration values for the machine. For example, If the computer’s network information is shown as follows: - IP address: 169. 254. 133. 42 - Subnet Mask: 255. 255. 0. 0 Then, the machine’s network information should be as shown below: - IP address: 169. 254. 133. 43 13 When the window that tells you that the network cable connection is confirmed appears, disconnect the network cable and click Next. If the network cable is connected, it may have trouble finding the machine when configuring the wireless network. 14 15 The wireless network connects according to the network configuration. After installation is finished, click Quit. After completing the wireless network connection, you need to install a machine driver to print from an application (see "Installation for Mac" on page 142). 2. Using a Network-Connected Machine 184 Wireless network setup 18 Printing a network configuration report Using a network cable You can identify the network settings of your machine by printing a network configuration report. Machines that do not support the network port will not be able to use this feature (see "Rear view" on page 22). See "Printing a network configuration report" on page 148. Your machine is a network compatible machine. To enable your machine to work with your network, you will need to perform some configuration procedures. IP setting using SetIP Program (Windows) This program is used to manually set the network IP address of your machine using its MAC address to communicate with the machine. The MAC address is the hardware serial number of the network interface and can be found in the Network Configuration Report. See "Setting IP address" on page 148. • After completing the wireless network connection, you need to install a machine driver to print from an application (see "Installing driver over the network" on page 151). • See your network administrator, or the person that set up your wireless network, for information about your network configuration. Configuring the machine’s wireless network Before starting you will need to know the network name (SSID) of your wireless network and the network key if it is encrypted. This information was set when the access point (or wireless router) was installed. If you do not know about your wireless environment, please ask the person who set up your network. To configure wireless parameters, you can use SyncThru™ Web Service. Items to prepare • • • • • Access point Network-connected computer Software CD that was provided with your machine A machine installed with a wireless network interface Network cable 2. Using a Network-Connected Machine 185 Wireless network setup Using SyncThru™ Web Service Before starting wireless parameter configuration, check the cable connection status. Wizard will help you setup the wireless network configuration. However, if you want to set the wireless network directly, select Custom. 1 2 Check whether or not the network cable is connected to the machine. If not, connect the machine with a standard network cable. Start a web browser such as Internet Explorer, Safari, or Firefox and enter your machine’s new IP address in the browser window. For example, 7 Select the one Network Name(SSID) in the list. [. . . ] It is a client-server protocol, where the client transmits an email message to the server. Transmission Confirmation Report (TCR) provides details of each transmission such as job status, transmission result and number of pages sent. This report can be set to print after each job or only after failed transmissions. TIFF Tagged Image File Format (TIFF) is a variable-resolution bitmapped image format. TIFF describes image data that typically come from scanners. [. . . ]