User manual SAMSUNG SM320MXN QUICK GUIDE

[. . . ] LCD MONITOR quick start guide 320MX 320MXn Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Note This stand is not for the Floor Standing Type. Unpacking LCD Display Manuals Quick Setup Guide Warranty Card (Not available in all locations) User's Guide Cables D-Sub Cable Others Power Cord Introduction Others Remote Control Batteries (AAA X 2) (Not available in all locations) Sold separately DVI Cable Wall Mount KIT LAN Cable (Applicable to the MXn model only) TV tuner box NetWork Box (Applicable to the MX model only) Semi Stand KIT Note · · You can purchase and connect a separate network box or TV tuner box. [. . . ] Contact a local SAMSUNG Electronics Service Center to buy optional items. Connecting to Other devices Using a Power cord with Earth · In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When unwiring the earth lead, make sure to disconnect the AC power in advance. Note AV input devices such as DVD players, VCR's or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the contents under Adjusting Your LCD Display. Connecting AV Devices 1. 3. Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [R-AUDIO-L] port of the LCD Display. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted. Note The LCD Display has AV connection terminals to connect AV input devices like DVDs, VCRs or Camcorders. You may enjoy AV signals as long as the LCD Display is turned on. Connections Connecting to a Camcorder 1. Locate the A/V output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the AV AUDIO IN [L-AUDIO-R] on the LCD Display . Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN [VIDEO] on the LCD Display . Select AV for the Camcorder connection using the Source button on the front of the LCD Display or on the remote control. Then, start the Camcorders with a tape inserted. 4. The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store. ) If your camcorder is stereo, you need to connect a set of two cables. Connecting Using a HDMI Cable Note · · Input devices such as digital DVD are connected to the HDMI terminal of the LCD Display using the HDMI cable. You cannot connect a PC to the HDMI terminal. Connections Connecting Using a DVI to HDMI Cable Note · · Connect the DVI output terminal of a digital output device to the HDMI terminal of the LCD Display using a DVI to HDMI cable. However, you will receive the following message for a minute; You can choose to change the screen resolution or stay in the current mode during that time. And if the resolution is more than 85Hz, you will see the black screen because the LCD Display does not support over 85Hz. Note Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the LCD Display. Maintenance and Cleaning 1) Maintaining the LCD Display Case. Clean with a soft cloth after disconnecting the power cord. Troubleshooting · · Do not use benzene, thinner or other flammable substances, or a wet cloth. We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. · Never use acetone, benzene or thinner. [. . . ] Choose the ghost image to update your USB disk with and choose the target disk. 6) When the ghost image update finishes, the set will be rebooted automatically. Q&A Q: A: How can I change the frequency?The frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. [. . . ]