User manual SAMSUNG SMO-120P

[. . . ] COLOR DUAL QUAD OBSERVATION SYSYTEM SMM-15FDQ/21FDQ User Guide Manuel d'utilisation Guía del usuario IMPORTANT SAFETY INSTRUCTIONS 1. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] Choose an installation site that can sufficiently support the weight of the equipments to be installed. Attach the camera mount bracket to the wall or ceiling using the supplied three screws (M4 X L15). Adjust the camera to target the video location and tighten the bracket handle on the camera mount bracket. 4x15 sized screws wall or ceiling English-15 3) PIR Camera composition (Top) (Bottom) 3 5 4 1 2 Lens It has a focal length of 3. 8mm and makes it possible for you to observe a relatively wide area. Speaker It outputs the sound signal which was transfered from the monitor. Fresnel Lens An infrared focusing lens for increasing the sensitivity of the built-in PIR sensor. English-16 6-pin modular jack Used to connect the camera to the monitor. PIN NUMBER !@ # $ % ^ SPEC SPEAKER(HOT) VIDEO_OUT GND SPEAKER(COLD) AUDIO_OUT/ALARM_OUT 12V DC 5-Pin Terminal Block A terminal block for supplying backup power for the PIR sensor operation during power outages and for transmitting the relay signals to external devices during the PIR sensor operation. PIN !@ # $ % Power Input (Back Up) Relay Output (350V 130mA) SPEC DC 12 Volts Ground Not Used COM N. C 5 4 3 2 1 English-17 (Sensor Detection Angle & Area) 1) Vertical View Pattern 2) Horizontal View Pattern English-18 (Inside) 6 7 8 9 Function Switch A function switch for the PIR sensor operation. ON PIN ! Function Sensor Sensitivity On, On : Low On, Off : Normal Off, On : Normal Off, Off : High Alarm Led On/Off (Sensor On) Sensor On/Off OFF S1 !S2 @ S3 # S4 $ @ # $ PIR Sensor A thermal heat sensor that detects infrared radiation projected by warm objects. Microphone Capable of picking up all sound in the vicinity of the camera location and transmitting to the monitor. Electronic Relay Output power is 350V/130mA. English-19 Camera installation Hints 1. Do not install directly towards rising or setting sun. Can cause burn or damage to internal options. Do not limit desired detection zone by interference of curtains, screens, potted plants, etc. Also, do not locate it in front of source of water/oil vapors. Avoid placement of heat source inside detection zone 4. Do not install outdoors. English-20 4) Installing the PIR Camera (SMM-PIRCAM) 1. Choose an installation site that can sufficiently support 5 times the weight of the equipments to be installed. Remove the screw (BH M2. 6) at the bottom of the main unit by turning it counterclockwise, and then lift the assy-case front as you push it upward to detach it from the case-rear. ( Do not apply excessive force, as doing so may damage the inside assembly. ) Assy-case front Screw (BH M2. 6) CASE-REAR 3. Place the case-rear over the installation site and mark screw holes with a pencil (indicated by the circles in the illustration). Drill a pilot hole for each pencil mark (5mm in diameter and at least 35mm in depth), and then fully insert the supplied plastic anchors (HUD 5) into them. English-21 4. Connect the Camera connector(RJ-11) cable to the case-rear as well as the cable to be connected to the terminal. 5. [. . . ] (ON: Buzzer operation, OFF: NA) English-37 3-7) VIEW EVENT LOG MENU function and setting method · · Function: Displays the time and date of camera event and type of event. VIEW EVENT LOG MENU by using oeENTER SWITCH at SETUP MENU, then press the ENTER SWITCH to display the OSD as shown in the figure below. (The figure shows the initial setting status. ) 06/01/03 13:14:00 NO CH 07 01 01 02 01 01 01 01 MM/DD/YY 02/10/03 02/11/03 06/01/03 06/01/03 --/--/---/--/---/--/---/--/-- HH:MM:SS 10:00:30 11:22:00 12:33:01 13:01:03 --:--:---:--:---:--:---:--:-- EVT A L - Sequence of event happening Camera No. Date of event happening 01 02 03 04 05 06 07 08 Type of event happening L : LOSS A : ALARM Time of event happening An event which occurred most recently is recorded with first priority, then users can move to the next page by using oeENTER SWITCH. [. . . ]