User manual SAMSUNG SMO-150QP

[. . . ] COLOR DUAL QUAD OBSERVATION SYSTEM SMO-150QP User Guide Manuel d'utilisation Bedienungsanleitung Guía del usuario Guida dell'utente êÛÍÓ, ÓÒÚ, Ó ÔÓθÁÓ, ÚÂÎfl Gebruikershandleiding IMPORTANT SAFETY INSTRUCTIONS 1. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] Electronic Relay Output power is 350V/130mA. English-19 Camera installation Hints 1. Do not install directly towards rising or setting sun. Can cause burn or damage to internal options. Do not limit desired detection zone by interference of curtains, screens, potted plants, etc. Also, do not locate it in front of source of water/oil vapors. Avoid placement of heat source inside detection zone. Do not install outdoors. English-20 4) Installing the PIR Camera (SOC-C321P) 1. Choose an installation site that can sufficiently support 5 times the weight of the equipments to be installed. Remove the screw (BH M2. 6) at the bottom of the main unit by turning it counterclockwise, and then lift the assy-case front as you push it upward to detach it from the case-rear. ( Do not apply excessive force, as doing so may damage the inside assembly. ) Assy-case front Screw (BH M2. 6) CASE-REAR 3. Place the case-rear over the installation site and mark screw holes with a pencil (indicated by the circles in the illustration). Drill a pilot hole for each pencil mark (5mm in diameter and at least 35mm in depth), and then fully insert the supplied plastic anchors (HUD 5) into them. English-21 4. Connect the Camera connector (RJ-11) cable to the case-rear as well as the cable to be connected to the terminal. 5. Align the two holes of the case-rear to the holes of the plastic anchors, and then fasten the screw-tappings (BH M3 X 30). SCREW-TAPPING G(BH M3 x 30) SCREW-TAPPING G(BH M3 x 30) English-22 6. 1) Use the cross (+) screw driver to turn the screw (indicated by the arrow in the illustration) counterclockwise slightly. 2) Tilt the lens body down about 10° from the horizontal, and then turn the screw clockwise to fasten it. Screw (HB M4 x L8) 7. Assemble the assy-case front onto the case-rear as shown in the illustration. Fasten the assy-case front to the case-rear with the screw (BH M2. 6) you removed earlier. CASE-REAR Screw (BH M2. 6) ASSY-CASE FRONT English-23 Installing the Camera using the Mount-Corner 1. Choose an installation site that can suffi ciently support 5 times the weight of the equipments to be installed. Place the mount-corner to the corner to which you want to install the camera and mark screw holes with a pencil (indicated by the blue circles in the illustration). Drill a pilot hole for each pencil mark (5mm in diameter and at least 35mm in depth), and then fully insert the supplied plastic anchors (HUD 5) into them. 3. Install the mount-corner by aligning the four holes of the mount-corner to the holes of the plastic anchors, and then fastening the screw-tappings (BH M3 X 30). SCREWTAPPING (BH M3 x 30) SCREWTAPPING (BH M3 x 30) English-24 4. [. . . ] (4) BUZZER item sets whether or not buzzer device set in monitor is used at an ALARM or LOSS occurring. (ON: Buzzer operation, OFF: NA) English-41 3-7) VIEW EVENT LOG MENU function and setting method · · Function: Displays the time and date of camera event and type of event. VIEW EVENT LOG MENU by using oeENTER SWITCH at SETUP MENU, then press the ENTER SWITCH to display the OSD as shown in the figure below. (The figure shows the initial setting status. ) 06/01/03 13:14:00 NO CH 07 01 01 02 01 01 01 01 MM/DD/YY 02/10/03 02/11/03 06/01/03 06/01/03 --/--/---/--/---/--/---/--/-- HH:MM:SS 10:00:30 11:22:00 12:33:01 13:01:03 --:--:---:--:---:--:---:--:-- EVT A L - Sequence of event happening Camera No. [. . . ]