User manual SAMSUNG SP-43L2H

[. . . ] COLOUR TELEVISION SP43L2HX SP50L2HX SP61L2HX Owner's Instructions Before operating the unit, please read this manual thoroughly, and retain it for future reference. ON-SCREEN MENUS PICTURE IN PICTURE (PIP) TELETEXT Safety Instructions ENG Do not expose the television to extreme temperature conditions or to extreme humidity conditions. Do not expose the television to direct sunlight and other sources of heat. Do not expose the television to any liquids. Never put objects of any kind into the television, and do not place a water-containing vessel on the television. [. . . ] The options available in the Picture group are Result: displayed. Result: Select the option by moving the joystick left or right. The following modes are available depending on the Result: input source. Custom - Dynamic - Standard - Movie Custom - High - Middle - Low (PC or DVI Mode) 2 3 22 You can also set these options simply by pressing the P. STD (Picture Standard) button. Adjusting the Picture Settings ENG Your television has several settings which allow you to control picture quality. Mode Picture Custom Auto Wide Off Off Off Move Enter 1 Press the MENU button. Result: The options available in the Picture group are displayed. Adjust Size Blue Screen Film Mode Digital NR 2 3 Move the joystick right. Move the joystick up or down until the Adjust option is selected. Result: The Adjust menu is displayed with the Colour Tone option is selected. Adjust (Custom) Colour Tone Contrast Brightness Sharpness Colour Move oe Sel. oe Normal 50 50 90 50 Store 4 Select the option by moving the joystick left or right. The colour tones are displayed in the following order. Normal - Warm1 - Warm2 - Cool2 - Cool1 5 Move the joystick up or down to select the option (Contrast, Brightness, Sharpness, Colour) to be adjusted. Result: The horizontal bar is displayed. Move the horizontal bar's cursor left or right by moving the joystick left or right. mode is set to Custom, the value of these When the picturebe changed depending on the input source option may vary (ex. RF, Video, Component, PC or DVI). 6 When you are satisfied with the settings, press the joystick button ( ) to store them. If you make any changes to these settings, the picture standard is automatically switched to the Custom 23 Adjusting the Picture Settings (PC or DVI Mode) ENG 1 Picture Mode Adjust Colour Tone Colour Adjust Custom Custom Preset to the PC mode by using the Source button. Press the MENU button. Result: The options available in the Picture group are displayed. 2 3 Move the joystick right. Move the joystick up or down until the Adjust option is selected. Result: The Adjust menu is displayed. Move Enter 4 Adjust (Custom) Contrast Brightness 75 60 Move the joystick up or down to select the option (Contrast, Brightness ) to be adjusted. Result: The horizontal bar is displayed. Move the horizontal bar's cursor left or right by moving the joystick left or right. 5 Move oe Adjust Store Press the MENU button. Result: The options available in the Picture group are displayed again. Picture Mode Adjust Colour Tone Colour Adjust Custom Custom 6 7 Move the joystick up or down until the Colour Tone option is selected. Select the option by moving the joystick left or right. The colour tones are displayed in the following order. Custom - Colour1 - Colour2 - Colour3 8 Move oe Sel. Move the joystick up or down until the colour Adjust option is selected. [. . . ] Clock- Pins 5, 7, 9, 11, 13, 15 and 16 are used for RGB processing and are only wired on the AV1 or AV3 connector. PC Input Connector (15Pin) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PC IN Red (R) Green (G) Blue (B) Grounding Grounding (DDC) Red (R) Grounding Green (G) Grounding Blue (B) Grounding Reserved Sync Grounding Grounding Data (DDC) Horizontal sync. Clock (DDC) RS-232 Connector (9Pin) Pin 1 2 3 4 5 6 7 8 9 Signal Carrier Detect Receive Data Transmit Data Data Terminal Ready System Ground Data Set Ready Request to Send Clear to Send Ring Indicator 50 Troubleshooting: Before Contacting Service Personnel ENG Before contacting Samsung after-sales service, perform the following simple checks. If you cannot solve the problem using the instructions below, note the model and serial number of the television and contact your local dealer. No sound or picture Check that the mains lead has been connected to a wall socket. [. . . ]