User manual SAMSUNG SP-47Q5HL

[. . . ] SP42Q2HL SP47Q2HL SP52Q2HL SP54T8HL SP43Q5HL1X SP47Q5HL1X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PROJECTION TELEVISION . . . . . . . . . . . . . Owner's Instructions Register your product at www. samsung. com/global/register Important Warranty Information Regarding Television Format Viewing Standard screen format televisions (4:3, the aspect ratio of the screen width to height) are primarily designed to view standard format full-motion video. The images displayed on them should primarily be in the standard 4:3 ratio format and constantly moving. Displaying stationary graphics and images on screen, such as the dark top and bottom letterbox bars (wide screen pictures), should be limited to no more than 15% of the total television viewing per week. [. . . ] Press the or button to select "Red" or "Blue". TV Setup Time Plug & Play Language : English Self Focus Manual Convergence More Move Enter Return TV Manual convergence Red Blue Reset Move Enter Return continued. . . English - 24 O P E R AT I O N 3 Press the ENTER button. A crosshatch pattern will appear on the screen. Move the cursor to the position you want to adjust by pressing the //oe/ buttons, then press the ENTER button. Adjust the convergence by pressing the //oe/ buttons, then press the ENTER button. Red Please, use remote control. oe Move Enter Return Red Please, use remote control. oe Adjust Enter Return 4 If a horizontal line is visible, use the or button to move the line so that it is superimposed on the horizontal center-line (i. e. , make a single horizontal line that is as white as possible. ). Red Please, use remote control. oe Adjust Enter Return 5 If a vertical red is visible, use the oe or button to move the line so that it is superimposed on the vertical-center line (i. e. , make a single vertical line that is as white as possible. ) After the convergence is correctly adjusted, press the MENU button to exit. Red Please, use remote control. oe Adjust Enter Return 6 To return to the factory defaults, select "Reset" by pressing the or button, then press the ENTER button. The previously adjusted convergence will be reset to the factory defaults. TV Manual convergence Red Blue Reset Move Enter Return English - 25 O P E R AT I O N Memorizing the Channels Your TV can memorize and store all of the available channels for both "off-air" (antenna) and cable channels. After the available channels are memorized, use the CH and CH buttons to scan through the channels. This eliminates the need to change channels by entering the channel digits. Selecting the Video Signal Source Before your TV can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i. e. , an antenna or a cable system). 1 Press the MENU button. or button to select "Channel", then press the ENTER button. TV Channel Air/CATV : Air Auto Program Favorite Channels Fine Tune oe 00 Add/Delete Name oe --- Move Enter Return 2 Press the ENTER button to select "Air/CATV". or button to select "Air", "STD", "HRC" or "IRC", then press the ENTER button. TV Channel Air/CATV : Air STD Auto Program Favorite ChannelsHRC Fine Tune 00 oe IRC Add/Delete Name oe ---- oe If you are connected to an antenna, press the . . . oe If you connected cable, press the . . . or button to select the type of cable system: "STD", "HRC" or "IRC". Move Enter Return Press the EXIT button to exit. · "STD", "HRC" and "IRC" identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected. Proceed to "Storing Channels in Memory". · Subscription cable services require service-specific requirement for viewing. English - 26 O P E R AT I O N Storing Channels in Memory (Automatic Method) First, select the correct signal source ("Air", "STD", "HRC" or "IRC") as described on the previous page. 1 Press the MENU button. or button to select "Channel", then press the ENTER button. TV Channel Air/CATV : Air Auto Program Favorite Channels Fine Tune oe 00 Add/Delete Name oe --- Move Enter Return 2 Press the . . . or button to select "Auto Program", then press the ENTER button. Enter Auto Program Start Return Press the ENTER button to start the auto program. The TV begins memorizing all of the available stations. [. . . ] Press the MODE button to put your remote control in the TV mode. The visual qualities of digital channels may vary depending on the original production method (analog or digital). Classification by the information displayed when switching channels. If the original production method is digital: High visual quality program. [. . . ]