User manual SAMSUNG SR8F31

[. . . ] SR8F3* SERIES SR8F4* SERIES Robotic Vacuum Cleaner User Manual This manual is made with 100 % recycled paper. ✻ Before operating this unit, please read the instructions carefully. ✻ For indoor use only. English imagine the possibilities Thank you for purchasing a Samsung product. To receive a more complete service, please register your product at www. samsung. com/register DJ68-00695A(0. 0)-EN. indd 1 2013. 3. 11 5:8:39 PM Safety information SAFETY INFORMATION WARNING • Before operating the appliance, please read this manual thoroughly and retain it for your reference. • Because these following operating instructions cover various models, the characteristics of your vacuum cleaner may differ slightly from those described in this manual. [. . . ] If hair or string is wrapped between the main unit and the side rotating brush, undo the screw of the side rotating brush using a (+) driver to remove it. When reassembling the brush, check the “L” mark on the edge-cleaning side rotating brush and the “L” mark on the main unit and then reassemble the side rotating brush. (Letter “R” is carved at the right side rotating brush. ) L NOTE Because the side rotating brush easily attracts hair and other foreign substances, make sure to clean it frequently. Excessive foreign substances on the side rotating brush can damage the brush. 38_ Maintain tools and filter DJ68-00695A(0. 0)-EN. indd 38 2013. 3. 11 5:9:11 PM Maintain tools and filter CLEANING THE ROBOTIC VACUUM CLEANER CLEANING THE DRIVING WHEEL You must turn off the Power Switch at the bottom of the main unit before cleaning the robotic. 04 MAINTAIN TOOLS AND FILTER ■ If the robotic vacuum cleaner suddenly starts to zigzag, there may be foreign substances stuck on the driving wheel. 1. When cleaning the driving wheel, place a soft cloth on the floor and flip the main unit, placing it down carefully. 2. Check for foreign substances and remove them using a stick or a pair of blunt nippers if necessary. Maintain tools and filter _39 DJ68-00695A(0. 0)-EN. indd 39 2013. 3. 11 5:9:11 PM Troubleshooting CHECKLIST BEFORE SVC CALLS SYMPTOM Robotic vacuum cleaner does not operate at all before cleaning. CHECKLIST • Is the Dust bin assembled?• Is cleaning mode ( MEASURE TO TAKE • Install the Dust bin. • Press the ( ) in the display panel turned on? ) button. (To turn it off, press and hold the ( ) button down for 3 seconds or longer. ) • Is the battery level flashing only • Lift up the robotic vacuum one level and is ‘LO’ displayed in the display panel? • Robotic vacuum cleaner will not Robotic vacuum cleaner stopped operating while cleaning. The suction power is weak while cleaning. operate when the battery in the remote control is depleted. • Is the battery level flashing only • Lift up the robotic vacuum one level and is ‘LO’ displayed in cleaner, manually dock the the display panel?• Has the robotic vacuum cleaner • Turn off the Power Switch and become hooked on wires on the remove the wires. • Is the robotic vacuum cleaner • Turn off the Power Switch and stuck to the floor where there is a move the cleaning robotic height difference?vacuum to another place to - The driving wheel is lifted. • Is there a thin towel (cloth) • Turn off the Power Switch and wrapped around the driving remove the thin towel. • Is the robotic vacuum cleaner • Turn off the Power Switch and stuck on the doorsill?move the robotic vacuum cleaner to another place to clean. • Check whether the Dust bin • Stop the robotic vacuum cleaner is full of dust. • Check whether the suction • Turn off the Power Switch and inlet is clogged by foreign remove the foreign substances substances. on the suction inlet. • Check whether the Filter is • Clean the Filter well. cleaner, and manually dock the robotic vacuum onto the charger to charge it. • Replace the batteries in the remote control. (AAA type) clogged. 40_ Troubleshooting DJ68-00695A(0. 0)-EN. indd 40 2013. 3. 11 5:9:12 PM Troubleshooting CHECKLIST BEFORE SVC CALLS SYMPTOM Robotic vacuum cleaner cannot find the charger. [. . . ] END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Libraries If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found. [. . . ]