User manual SAMSUNG SRP-370

[. . . ] Safety Precautions USER'S MANUAL SRP-370/372 THERMAL RECEIPT PRINTER In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. WARNING Violating following instructions can cause serious injury or death. You must use only the supplied adapter. It is dangerous to use other adapters. Do not plug several products in one multi-outlet. This can provoke over-heating and a fire. If the plug is wet or dirty, dry or wipe it before usage. If the plug does not fit perfectly with the outlet, do not plug in. Be sure to use only standardized multi-outlets. ONLY SUPPLIED ADAPTER PROHIBITED Do not pull the cable to unplug. Keep the plastic bag out of children's reach. If not, a child may put the bag on his head. This can damage the cable, which is the origin of a fire or a breakdown of the printer. PROHIBITED PROHIBITED Do not plug in or unplug with your hands wet. You can be electrocuted. If you observe a strange smoke, odor or noise from the printer, unplug it before taking following measures. Switch off the printer and unplug the set from the mains. [. . . ] ESC a n [Name] [Format] [Range] [Default] [Description] Select justification. ASCII ESC a n Hex 1B 61 n Decimal 27 97 n 0 n 2, 48 n 50 n=0 In standard mode, aligns all the data in one line to the position specified by n as follows : n Justification 0, 48 Left justification 1, 49 Centering 2, 50 Right justification Off/On Off On Off On Off On Off On - This command is available only with a parallel interface and is ignored with a serial interface. Select paper sensor(s) to stop printing. ASCII ESC c 4 n Hex 1B 63 34 n Decimal 27 99 52 n 0 n 255 n=0 Selects the paper sensor(s) to use to stop printing when a paper end is detected. Hex 00 01 00 02 Decimal 0 1 0 2 Function Paper roll end Paper roll end Paper roll end Paper roll end Reserved. Bit 0 1 2~7 Off/On Off On Off On - sensor sensor sensor sensor disable. enable. 52 53 ESC c 5 n [Name] [Format] [Range] [Default] [Description] [Notes] Enable / Disable ASCII Hex Decimal panel button. ESC c 1B 63 27 99 5 35 53 n n n ESC t n [Name] [Format] [Range] [Default] [Description] 0 n 255 n=0 Enables or disables the panel buttons. - When the LSB of n is 0, the panel buttons are enabled. - When the LSB of n is 1, the panel buttons are disabled. When the printer cover is open, the panel buttons are always ignored regardless of the setting with this command. ESC d n [Name] [Format] [Range] [Description] Print and feed n lines. ASCII ESC Hex 1B Decimal 27 d 64 100 n n n 0 n 255 Prints the data in the print buffer and feeds n lines. ESC p m t1 t2 [Name] Generate pulse. [Format] ASCII ESC p m t1 t2 Hex 1B 70 m t1 t2 Decimal 27 112 m t1 t2 [Range] m = 0, 1, 48, 49 0 t1 255, 0 t2 255 [Description] Outputs the pulse specified by t1 and t2 to connector pin m as follows : m Connector pin 0, 48 Drawer kick-out connector pin 2 1, 49 Drawer kick-out connector pin 5 t1 specifies the pulse ON time as [t1 x 2ms], and t2 specifies the pulse OFF time as [t2 x 2ms]. If t2 is smaller than t1, OFF time is set as [t1 x 2ms]. Select character code table. ASCII ESC t n Hex 1B 74 n Decimal 27 116 n 0 n 5, 16 n 24, 27 n 30, n=255 For model without Thai character support : n=0 For model with Thai character support : n = 20 Selects a page n from the character code table. n Page 0 PC437 (USA, standard Europe) 1 Katakana 2 PC850 (Multilingual) 3 PC860 (Portuguese) 4 PC863 (Canadian-French) 5 PC865 (Nordic) 7 855 (Cyrillic) 8 857 (Turkish) 16 WPC1252 17 PC866 (Cyrillic #2) 18 PC852 (Latin 2) 19 PC858 (Euro) 22 864 (Arabic) 23 Thai character code 42 24 1253 (Greek) 28 1251 (Cyrillic) 29 737 (Greek) 31 Thai character code 16 33 1255 (Hebrew) 255 User-defined page ESC { n [Name] [Format] [Range] [Default] [Description] Turns upside-down printing mode on/off. ASCII ESC { n Hex 1B 7B n Decimal 27 123 n 0 n 255 n=0 Turns upside-down printing mode on or off. - When the LSB of n is 0, upside-down printing mode is turned off. - When the LSB of n is 1, upside-down printing mode is turned on. 54 55 FS p n m [Name] [Format] [Range] [Description] Print NV bit image. ASCII FS p Hex 1C 70 Decimal 28 112 1 n 255 0 m 3, 48 m 51 Prints an NV bit image n in m mode. Vertical Dot Density (DPI) 180 dpi 180 dpi 90 dpi 90 dpi Vertical Dot Density (DPI) 203 dpi 203 dpi 203/2 dpi 203/2 dpi n n n m m m GS !n [Name] [Format] [Range] [Default] [Description] - For SRP-370 : m Mode 0, 48 Normal 1, 49 Double-width 2, 50 Double-height 3, 51 Quadruple - For SRP-372 : m Mode 0, 48 Normal 1, 49 Double-width 2, 50 Double-height 3, 51 Quadruple dpi : dots per 25. 4mm {1"} Horizontal Dot Density (DPI) 180 dpi 90 dpi 180 dpi 90 dpi Horizontal Dot Density (DPI) 203 dpi 203/2 dpi 203 dpi 203/2 dpi FS q n [xL xH yL yH d1. . . dk]1. . . [xL xH yL yH d1. . . dk]n Defined NV bit image. [Name] ASCII FS q n [Format] [xL xH yL d1. . . dk]1. . . [xL xH yL d1. . . dk]n Hex 1C 71 n [xL xH yL d1. . . dk]1. . . [. . . ] Drawer kick-out connector status (n=2, 50) : AAWBit Off/On Hex Decimal Function Off 00 0 Drawer kick-out connector pin 3 is LOW. 0 Drawer kick-out connector pin 3 is HIGH. 7 Off 00 0 Fixed. Prints a raster bit image in m mode. <For SRP-370> m Mode Vertical dot density 0, 48 Normal 180 dpi 1, 49 Double-width 180 dpi 2, 50 Double-height 90 dpi 3, 51 Quadruple 90 dpi <For SRP-372> m Mode Vertical dot density 0, 48 Normal 203 dpi 1, 49 Double-width 203 dpi 2, 50 Double-height 203/2 dpi 3, 51 Quadruple 203/2 dpi Horizontal dot density 180 dpi 90 dpi 180 dpi 90 dpi Horizontal dot density 203 dpi 203/2 dpi 203 dpi 203/2 dpi dpi : dots per 25. 4mm {1"} - xL, xH specifies (xL + xH x 256) byte(s) in the horizontal direction for the bit image. [. . . ]