User manual SAMSUNG SRS600NLS

[. . . ] Refrigerator user manual This manual is made with 100% recycled paper. English imagine the possibilities Thank you for purchasing a Samsung product. To receive a more complete service, please register your product at www. samsung. com/register Free Standing Appliance safety information safETy inforMaTion WarninG see which refrigerant is used for the refrigerator. · In case of R600a refrigerant, this gas is natural gas with high environmental compatibility that is, however, also combustible. When transporting and installing the appliance, care should be taken to ensure that no parts of the refrigerating circuit are damaged. [. . . ] Remove the dust cap from the water line on the rear of the unit and fit a compression nut from the install kit. Remove the water pipe from the install kit and fit a compression nut to one end. Join the two pipes together using the compression joint from the install kit ensuring that the joint is water tight. Join the other end of the install pipe to the main water supply and turn on the water to check for leaks. insTaLLinG THE WaTEr DisPEnsEr LinE ForInteriormodel PartsforwaterlineInstallation 1 Water line fixer and 2 Pipe connector screws Loosen a remove cap Water Line from unit 3 Water line 4 Water filter no gap Connectingtothewatersupplyline 1. First, shut off the main water supply line. Locate the nearest cold, drinking water line. Follow the water line installation instructions in the installation kit. CAUTION The water line must be connected to the cold water pipe. If it is connected to the hot water pipe, it may cause the purifier to malfunction. CaUTion Water Line from Kit Only connect the water line to a drinkable water source. If you have to repair or disassemble the water line, cut off 6. 5mm of the plastic tubing to make sure you get a snug, leak-free connection. Before being used, the leakage in these places should be examined setting up _11 · Samsung Warranty does not cover WATER LINE INSTALLATION. · The cost of connection to a water supply is at the customer expense, unless included in the delivery charge (refer to the delivery agreement with the seller) · Please contact Plumber or Authorised Installer for the installation if needed. · If Water leakage occurs due to improper installation, Please contact installer. insTaLLinG THE WaTEr DisPEnsEr LinE ForExteriormodel PartsforwaterlineInstallation Pipe connector Water line fixer and screws Water line Purifier lock-clip Purifier Connectingtothewatersupplyline Connect the water pipe with coupler and tap. Connect coupler "A" to the tap. CAUTION The water line must be connected to the cold water pipe. If it is connected to the hot water pipe, it may cause the purifier to malfunction. WARRANTYINFORMATION This water line installation is not covered by the refrigerator or ice maker manufacturer's warranty. Follow these instructions carefully to minimise the risk of expensive water damage. Note: If the coupler does not fit on the current tap, go the nearest authorised service dealer and purchase the right couplers fittings. Selectthelocationwherethepurifier istoinstall. (Modelwiththepurifier) - If you wish to reassemble the water inlet and outlet sides of the purifier during purifier installation, see the reference illustration. - Cut the water line attached to the purifier to the appropriate place after measuring the distance between the purifier and the cold water tap. 12_ setting up CoUPLEr "a" Removeanyresidualmatterinside thepurifier. (Modelwiththepurifier) - Open the main water tap to check whether water is running through the water tube on the water inlet side of the purifier. - If water does not come out through the line, check whether the tap is open. - Leave the tap open until clean water is running out and any residual matter that built up during manufacturing has been removed. oUTLET siDE of PUrifiEr PUrifiEr TaP LinE oUTLET 01 sETTinG UP siDE of PUrifiEr PUrifiEr WaTEr 90 degree CaUTion insert Locking Clip after tube seated WaTEr WaTEr inLET siDE of PUrifiEr CoUPLEr Locking Clip WaTEr LinE ReplacementInstructions 1. Insert water supply tube into the inlet side of the filter until the tube stop. fLoW DirECTion Attachthepurifierlock-clip. - Hold the purifier lock-clip in the appropriate position (under the sink for example) and fix it tightly into place where to screw. WaTEr sUPPLy inLET siDE PErMEaT Purifier lock-clip Note: You must also ensure that the cut is square and not at any sort of angle as this could cause a leak 4. After inserting tube, put together the clip strongly. [. . . ] Did you manually stop the ice making function?Make sure Ice Type is set to Cubed or Crushed. Is there any ice blocked within the ice storage unit?Try setting the freezer temperature lower. [. . . ]