User manual SAMSUNG SSC-1000

[. . . ] CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Graphic Symbol Explanation The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Warning-To Prevent Fire or Shock Hazard, Do Not Expose This Equipment To Rain or Moisture. 1 User's Guide IMPORTANT SAFEGUARDS 1. Read instructions: All the safety and operating instructions should be read before the appliance is operated. [. . . ] 13) AUX1~AUX4 This controls the AUX output of the Receiver Unit 14) SEQUENCE This is used when executing the Sequence switching actions set up in the Matrix Switcher. Also, if you press this button in the SALVO Mode, it becomes SALVO Switching Mode. 15) TOUR This is used when executing the TOUR Program set up in the Matrix Switcher. 16) SALVO This is used when executing the SALVO Program set up in the Matrix Switcher. 17) F1 This is used when confirming the ALARM List stored in the Matrix Switcher. 18) HOLD This is used when stopping the Switching mode of the SEQUENCE, TOUR, and SALVO of the Matrix Switcher. 10 19) NEXT This is used when proceeding the visuals one step at a time in the Switching HOLD Mode of the Matrix Switcher. 20) BEFORE This is used when returning the visuals one step at a time in the Switching HOLD Mode of the Matrix Switcher. 21) ENTER This is used when deciding the selected item or the set-up value. 24 23 22 MATRIX IN RX OUT DC 9V 0. 6A 22) DC9V 0. 6A This is the DC9V power input terminal. 23) IN-RX-OUT As being for RS-485 communication, this is connected to the Samsung Dome Camera or the RS-485 terminal of a different Controller. 24) MATRIX This is connected to the RS-485 terminal of the Matrix Switcher. 11 User's Guide 3. Installation and Connection MATRIX IN RX OUT DC 9V 0. 6A ADAPTOR MATRIX SWITCHER SAMSUNG DOME CAMERA /RECEIVER UNIT MATRIX IN RX OUT DC 9V 0. 6A CONTROLLER 1) Connect the RS-485 Cable. Connect the Samsung Dome Camera or the RS-485 cable of the receiver unit to the out terminal, and connect the RS-485 cable of a different controller to the RX in terminal, the RS-485 cable of the Matrix Switcher to the matrix terminal. For the RX terminal, number 3 (yellow) is DATA "+" and number 5(red) is DATA "­". For the matrix terminal, number 2 is DATA "+" and number 3 is DATA "­". Setting and Manipulating 1) Setting In order to enter into the set-up mode in the initial state, press the MENU button. MON = [ 0 0 ] CAM=[ 0 0 0 ] MANUAL SELECT MANUAL If you press the MENU button, words that ask for the password get indicated in LCD, and if you put in the password, the main menu gets indicated. When it is in password disable, it immediately enters the main menu. INPUT PASSWORD [ ] Select the item you want to set up from the main menu. Moves of items are done by the " " and " " buttons, and for selection, if you press the ENTER button, you enter the set-up menu of the item you desire. If you press on the MENU button in the main menu state, you can come out of the set-up mode. CONTROLLER SET If you select the controller set in the main menu, you can make set-ups related to the controller. Moves of items are done by the " " and " " buttons, and for selection, you can press the ENTER button. Next, move CURSOR( ) to position set, control pan/tilt and the lens, and press the ENTER button. If you want to cancel the concerned preset no. , move CURSOR( ) to delete, and press the ENTER button. [. . . ] If you press the NEXT or BEFORE button in this state, it gets converted to the next visuals or the previous visuals of the visuals being put out presently. If you want to automatically convert again, press the SEQUENCE button. If you want to convert the SEQUENCE RUN Mode to the manual select mode, press CAM+NO. +ENTER. 19 User's Guide TOUR action This is a function for putting out the Tour Switching program set up in the matrix switcher on the monitor of your discretion. First, select the monitor you intend to put out, and when you press TOUR+NO. +ENTER, the visuals corresponded to the pertinent Tour program get automatically converted, "TOUR [NO] RUN" get indicated in the LCD. [. . . ]