User manual SAMSUNG ST55W3PC ENG (VER.00056B)

[. . . ] ST42W5P/ST47W3PC ST55W3PC/ST65W3PC ST43T8PC/ST54T8PC ST62T8PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PROJECTION TELEVISION . . . . . . . . . . . . . Owner's Instructions BP68-00056B-00(ENG) Warning!Important Safety Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside. [. . . ] Press the CH button to select "Function", then press the VOL + button. Language Plug & Play Convergence Caption Time Function : English 2 Press the CH button to select "Language", then press the VOL + or VOL button to select the language. Press the Menu button to exit. Language Plug & Play Convergence Caption Time Function : English Selecting the Antenna Input You can connect to two different signal sources by choosing the antenna input (Antenna A or Antenna B). 1 Press the Menu button . Press the CH button to select "Channel", then press the VOL + button to enter. Antenna ANT/CATV Auto Program Fav. Channel Fine Tune Add/Erase Labeling Channel :A : ANT : 00 : ---- 2 Press the VOL + or VOL button to select "A" or " B". Press the Menu button to exit. Antenna ANT/CATV Auto Program Fav. Channel Fine Tune Add/Erase Labeling Channel :B : ANT : 00 : ---- CHAPTER THREE: TV OPERATION 3. 7 O P E R AT I O N Memorizing the Channels Your TV can memorize and store all of the available channels for both "off-air" (antenna) and cable channels. After the available channels are memorized, use the CH and CH buttons to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual). Selecting the Video Signal-source Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i. e. , an antenna or a cable system). 1 Press the Menu button. Press the CH button to select "Channel", then press the VOL + button. Antenna ANT/CATV Auto Program Fav. Channel Fine Tune Add/Erase Labeling Channel :A : ANT : 00 : ---- 2 Press the CH button to select "ANT/CATV", then Press the VOL + or VOL button to cycle through these choices: ANT (antenna), STD, HRC or IRC. Antenna ANT/CATV Auto Program Fav. Channel Fine Tune Add/Erase Labeling Channel :A : ANT : 00 : ---- Note: STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected. Proceed to "Storing Channels in Memory" (next page). 3. 8 CHAPTER THREE: TV OPERATION O P E R AT I O N Storing Channels in Memory (Automatic Method) 1 First, select the correct signal source (ANT, STD, HRC, IRC). Press the CH button to select "Channel", then press the VOL + button Antenna ANT/CATV Auto Program Fav. Channel Fine Tune Add/Erase Labeling Channel :A : ANT : 00 : ---- 2 Press the CH button to select "Auto Program", then press the VOL + button. Antenna ANT/CATV Auto Program Fav. Channel Fine Tune Add/Erase Labeling Channel :A : ANT : 00 : ---- 3 The TV will begin memorizing all of the available channels. After all the available channels are stored, the Auto program menu reappears. Press the Menu button to exit. The TV automatically cycles through all of the available channels and stores them in memory. This takes about one to two minutes. Adding and Erasing Channels (Manual Method) w 1 Use the number buttons to directly select the channel that will be added or erased. 2 Press the Add/Erase button: Repeatedly pressing this button will alternate between "Added" and "Erased. " Press the Menu button to exit. You can view any channel (including an erased channel) by using the number buttons on the remote control. CHAPTER THREE: TV OPERATION 3. 9 O P E R AT I O N Changing Channels Using the Channel Buttons Press the CH or CH button to change channels. When you press CH or CH , the TV changes channels in sequence. You will see all the channels that the TV has memorized. [. . . ] When your remote control is in the "VCR" (or DVD) mode, the volume buttons still control your TV's volume. When your remote is in the "TV" mode, the VCR control buttons (PLAY, PAUSE, etc. ) will still operate your VCR. M M 5 Press the Power button on the remote control. If your VCR (or DVD) turns on, your remote control is now set correctly. M 6 Once your remote control is set up, press the MODE button any time you want to use the remote to operate your VCR (or DVD). CHAPTER FOUR: SPECIAL FEATURES 4. 15 S P E C I A L F E AT U R E S Setting Up Your Remote Control to Operate Your Cable Box 1 Turn off your cable box. 2 Press the MODE button and make sure that the Cable LED is illuminated. The remote control has four "modes": "TV, " "VCR, " "CABLE" and "DVD. " Press the "MODE" button to switch the remote control to the "Cable" mode. M 3 On your Samsung remote control, press SET. 4 Enter 3 digits of the cable box code listed below for your brand of cable box. Make sure you enter 3 digits of the code, even if the first digit is a "0. " (If more than one code listed, try the first one. ) M 5 Press Power. If your cable box turns on, your remote control is now "set up" correctly. If your cable box does not turn on, repeat steps 2, 3, and 4, but try one of the other codes listed for your particular brand of cable box. [. . . ]