User manual SAMSUNG STP-102S REV 2.0

[. . . ] 2001 MANUAL REVISION 2. 0 STP-102S / STP-102P Operator's Manual This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interface when the equipment is operated in a commercial environment. This equipment generates uses, and can radiate radio frequency energy and, if not installed and uses in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Notice - Canada This Apparatus complies with class "A" limits for radio interference as specified in the Canadian department of communications radio interference regulations. Introduction The STP-102S and STP-102P Roll Printer is designed for use with electric instruments such as system ECR, POS, banking equipment peripheral equipment, etc. [. . . ] Ending the self-test After a number of lines are printed, the printer indicates the end of the self-test by printing " ** TEST COMPLETED ** ". If the self-test is completed, then you must reboot your printer. Followings are the self-test results with STP-102S and STP-102P. Chapter 6. Code Table The following pages show the character code tables. To find the character corresponding to a hexadecimal number, count across the top of the table for the For example, 4A=J. 13 14 PC850 : Multilingual PC860 : Portuguese 15 16 PC863 : Canadian - French PC865 : Nordic 17 18 Space Page 19 20 Chapter 7. Functions The commands listed in the table below are available for control of the printer. Commands Command HT LF ESC SP ESC !ESC $ ESC % ESC & ESC * ESC ESC 2 ESC 3 ESC ?ESC @ ESC D ESC E ESC J ESC R ESC S ESC V Horizontal tab Print and line feed Set right-side character spacing Select print mode(s) Set absolute print position Select/cancel user-defined character set Define user-defined characters Select bit-image mode Turn under line mode on/off Select 1/6-inch line spacing Set line spacing Cancel user-defined characters Initialize printer Set horizontal tab positions Turn emphasized mode on/off Print and feed paper Select an international character set Select standard mode Turn 90 clockwise rotation mode on/off Name Command Classification Executing Setting Standard Mode Command ESC \ ESC a ESC c5 ESC d ESC { GS $ GS / GS : GS B GS L GS P GS W GS ^ GS h GS k GS w Name Set relative print position Select justification Enable/disable panel buttons Print and feed paper n lines Turn upside-down printing mode on/off Select haracter size Define downloaded bit image Start/end macro definition Turn white/black reverse printing mode on/off Set left margin Set vertical and horizontal motion units Set printing area width Execute macro Set bar code height print bar code Set bar code width ( ) ( ) Command Classification Executing Setting Standard Mode Command classification Executing : Printer executes the command, which does not affect the following data. Setting : Printer uses flags to make setting, and those setting affect the following data. Standard mode ( ): : Enagled Enabled only when the command is used at the beginning of a line. : Enabled only when data is not present in the buffer. 21 22 Chapter 8. Control Commands ESC SP n [Name] [Format] [Range] [Description] Set right-side character spacing. ASCII ESC SP n Hex 1B 20 n Decimal 27 32 n 0 < n < 255 Sets the character spacing for the right side of the character to n dots. Command Notation [Name] [Format] The name of the command. Hex indicates the hexadecimal equivalents. Decimal indicates the decimal equivalents. [ ] k indicates the contents of the [ ] should be repeated k times. Gives the allowable ranges for the arguments. Describes the function of the command. ESC !n [Name] [Format] [Range] [Description] Bit 0 2 3 4 5 Select print modes. n Hex 1B 21 n Decimal 27 33 n 0 < n < 255 Selects print mode(s) using n as follows: Off/On Off On Off On Off On Off On Off On On Hex 00 01 00 08 00 10 00 20 00 80 02 Decimal 0 1 0 8 0 16 0 32 0 128 2 Function 24 char 42 char Undefined. 32 char [Range] [Description] Explanation of Terms LSB Least Significant Bit Control Commands HT [Name] [Format] [Description] Horizontal tab. HT ASCII 09 Hex 9 Decimal Moves the print position to the next horizontal tab position. 6 7 1 * Determine the values of n by adding the value of all the characteristics you want to select. LF [Name] [Format] [Description] Print and line feed. [. . . ] When the LSB is 0, white/black reverse printing mode is turned on. When the LSB is 1, white/black reverse printing mode is turned off. GS W nL nH [Name] [Format] [Range] [Description] [Notes] Set printing area width. ASCII GS W nL nH Hex 1D 4C nL nH Decimal 29 87 nL nH 0 < nL < 255 0 < nH < 255 Set the printing area width to the area specified by nL and nH. The printing area width is set to (nL + nH x 256) dots. [. . . ]