User manual SAMSUNG STP-131 REV 2.0

[. . . ] 2001 MANUAL REVISION 2. 0 STP131 Series Operator's Manual This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interface when the equipment is operated in a commercial environment. This equipment generates uses, and can radiate radio frequency energy and, if not installed and uses in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Notice - Canada This Apparatus complies with class "A" limits for radio interference as specified in the Canadian department of communications radio interference regulations. [. . . ] When the LSB of n is 1, the user-defined character set is selected. ESC !n [Name] [Format] [Range] [Description] Bit 0 1 2 3 4 5 6 7 Select print modes. n Hex 1B 21 n Decimal 27 33 n 0 < n < 255 Selects print mode(s) using n as follows: Hex 00 01 00 08 00 10 00 20 00 80 Decimal 0 1 0 8 0 16 0 32 0 128 Function Character font A (12 x 24) Character font B (9 x 24) Undefined. Underline mode selected. ESC & y c1 cw [x1 d1. . . d(y x x1). . . [xk d1. . . d(y x xk)] [Name] [Format] [Range] Define user-defined characters. ASCII ESC & y c1 c2[x1 d1. . . d(y x x1)]. . . [xk d1//d(y x xk)] Hex 1B 26 y c1 c2[x1 d1. . . d(y x x1)]. . . [xk d1//d(y x xk)] Decimal 27 38 y c1 c2[x1 d1. . . d(y x x1)]. . . [xk d1//d(y x xk)] y=3 32 < c1 < c2 < 126 0 < x < 12 Font A (12 x 24) 0 < x < 9 Font B ( 9 x 24) 0 < d1 . . . d(y x xk) < 255 Defines user-deined characters. y specifies the number of bytes in the vertical direction. c1 specifies the beginning character code for the definition, and c2 specifies the final code. x secifies the number of dots in the horizontal direction. Off/On Off On Off On Off On Off On Off On [Description] ESC * m nL nH d1. . . dk [Name] [Format] [Range] Select bit-image mode. dk m = 0, 1, 32, 33 0 < nL < 255 0 < nH < 3 0 < d < 255 Selects a bit-image mode using m for the number of dots specified by nL and nH, as follows: Vertical direction Number Dot of Dots Density 8 60 DPI 8 60 DPI 24 180 DPI 24 180 DPI Horizontal direction Dot Number of Data Density (k) 90 DPI nL + nH x 256 180 DPI nL + nH x 256 90 DPI (nL + nH x 256) x 3 180 DPI (nL + nH x 256) x 3 ESC-$ nL nH [Name] [Format] [Range] [Description] Set absolute print position. ASCII ESC $ nL nH Hex 1B 24 nL nH Decimal 27 36 nL nH 0 < nL < 255 0 < nH < 255 Set the distance from the beginning of the line to the position at with subsequent characters are to be printed. The distance from the beginning of the line to the print position is [(nL + nH x 256) x (vertical or horizontal motion unit)] inches. [Description] m 0 1 32 33 Mode 8-dot single-density 8-dot double-density 24-dot sigle-density 24-dot double-density 27 28 ESC - n [Name] [Format] [Range] [Description] n 0, 48 1, 49 2, 50 Turn underline mode on/off. ASCII ESC n Hex 1B 2D n Decimal 27 45 n 0 < n < 2, 48 < n < 50 Turns underline mode on or off, based on the following values of n: Function Turns off underline mode. Turns on underline mode (2-dots thick). ESC ?n [Name] [Format] [Range] [Description] Cancel user-defined characters. Hex 1B 3F Decimal 27 63 32 < n < 126 Cancels user-defined characters. n n n ESC @ [Name] [Format] [Description] Initialize printer. ASCII ESC @ Hex 1B 40 Decimal 27 64 Clears the data in the print buffer and resets the printer mode to the mode that was in effect when the power was turned on. ESC 2 [Name] [Format] [Description] Select default line spacing. ASCII ESC 2 Hex 1B 32 Decimal 27 50 Select 1/6-inch line (approximately 4. 23mm) spacing. ESC D n1. . . nk NUL [Name] [Format] Set horizontal tab positions. ESC D ASCII n1. . . nk NUL 1B 44 Hex n1. . . nk 00 27 68 Decimal n1. . . nk 0 1 < n < 255 0 < k < 32 Sets horizontal tab position. n specifies the column number for setting a horizontal tab position from the beginning of the line. k indicates the total number of horizontal ta positions to be set. ESC 3 n [Name] [Format] [Range] [Description] Set line spacing. [. . . ] m selects a bar code system as follows: m 0 1 2 3 4 5 6 65 66 67 68 2 1 Bar Code System UPC-A UPC-E JAN13(EAN13) JAN8(EAN8) CODE39 ITF CODABAR UPC-A UPC-E JAN13(EAN13) JAN8(EAN8) CODE39 ITF CODABAR CODE93 CODE128 Number of Characters 11 < k < 12 11 < k < 12 12 < k < 13 7<k<8 1<k 1 < k (even number) 1<k 11 < n < 12 11 < n < 12 12 < n < 13 7<n<8 1 < n < 255 1 < n < 255 (even number) 1 < n < 255 1 < n < 255 2 < n < 255 Gs f n [Name] [Format] [Range] [Description] n 0, 48 1, 49 Select font for Human Readable Interpreation(HRI) characters. ASCII GS f n Hex 1D 66 n Decimal 29 102 n n = 0, 1, 48, 49 Selects a font for the HRI characters used when printing a bar code. n selects a font from the following table: Font Font A (12 x 24) Font B (9 x 24) 69 70 71 GS h n [Name] [Format] [Range] [Description] Set bar code height. ASCII GS h n Hex 1D 68 n Decimal 29 104 n 1 < n < 255 Set the height of the bar code. [. . . ]