User manual SAMSUNG SU3364

[. . . ] I fvacuumcleanerisnotworkingasitshould, orhasbeendropped, damaged, left outdoors or dropped into water, return it to a service center. Donotpullorcarrybycord, usecordasahandle, closeadooroncord, orpull the cord around sharp edges or corners. Donotunplugbypullingonthecord. Tounplug, grasptheplug, notthecord. Donothandlevacuumcleanerorplugwithwethands. [. . . ] 3. nsertthescrewprovidedfromthescrewpacketintothe I existinghole. Tightensecurelywithascrewdriver. 01 ASEMBLING THE cLEANER ATTAcH DUST BIN TO VAcUUM Fit the groove located on the lower frontsideoftheDustBintothehook located on the vacuum body and attach the hook located on the DustBinHandletothevacuumbody as shown. ATTAcH VAcUUM HOSE AND TOOLS 1. ttachtheTwistSnapHosebyliningupthe A taps on the base with the corresponding notches on the back of the vacuum as shown. urntheTwistSnapHoseclockwisetolock T the hose into place. raspingtheHoseWand, slidetheendofthe G it onto the Hose Wand Base. Note : The vacuum will not operate effectively unless the Hose Wand is firmly attached. ttachtheLowerCordWrapbyliningup A the tab on the base with the corresponding notch on the back of the vacuum and turn it * Select Models Only clockwise as shown. ttachtheExtensionWandandtheCreviceTool A together into the holder on the right side of the body as shown. ttachtheCombinationToolintotheholderonthe A left side of the body as shown. ttachtheBracketBrushonthefrontofthehandle A andcliptheMiniTurboBrushintotheBracketBrushasshown. assembling the cleaner _7 Operating the cleaner pOWER SWITcH The Power Switch is located on the side of the vacuum. Pushtherockerswitch"ON"tovacuum, and"OFF" when cleaning is complete. HANDLE pOSITIONS Press the handle release pedal, located on the lower left side of the vacuum, with your foot to place your vacuum into one of three cleaning positions. Upright ­ For storage and above floor cleaning with tools. Normal cleaning ­ Press handle release pedal once. Position used for most household floor cleaning tasks. Low cleaning ­ With the vacuum in normal cleaning position, press handlereleasepedalagain. Useforreachingunder low furniture such as tables, chairs or beds. HEIGHT ADjUSTMENT The Powerfoot/Rotating Floor Brush can be adjusted to clean several floor surfaces. Note : Foroptimalcleaningperformance, adjusttothelowestpracticalsetting. Ifyour cleanerisdifficulttopush, adjusttothenexthighersetting. Alwaysensurethat the correct height setting is used for your flooring type as damage may occur if the height setting is not changed to reflect your flooring type. 1. TurnHeightAdjustmentKnobtodesiredsetting. Bare floor Setting ­ For bare floors. Medium Settings ­ For short and medium pile carpets. Highest Setting ­ For plush pile carpet TRANSpORTING cLEANER 1. omoveyourcleanerfromroomtoroom, T put the Handle in the upright position, tilt the cleaner back on its rear wheels and push forward. hecleanercanalsobemovedbyusingthe T Carrying Handle located on the top of the DustBin. 8_ operating the cleaner Carrying Handle Operating the cleaner SpEcIAL ON-BOARD TOOLS Your vacuum is not only a powerful carpet and rug cleaner, it's also a versatile above floor vacuum cleaner when you select one of the special tools. rasptheendoftheHoseWandandliftHoseWandtoseparatefromthe G Hose Wand Base. [. . . ] 4. nspectbelttoensurethatitisingoodcondition. If I brokenorcracked, pleasereplace. (Seebelowfor details. ) 5. With the curved ends facing down, slide end plates of brushbar into slots on the tool. oreplacebottomplate, insertthefourtabsonedge T of bottom plate into slots on front of tool. Pivot bottom plate down and snap closed. 03 MAINTENANcE Belt Replacement 1. Graspturbineandpullfirmlytoremove. [. . . ]