User manual SAMSUNG SU3485

[. . . ] · Use only as described in this manual. Use only manufacturer's recommended attachments. · Do not use with damaged cord or plug. · If vacuum cleaner is not working as it should, or has been dropped, damaged, left outdoors or dropped into water, return it to a service center. [. . . ] Tighten securely with a screwdriver. 01 ASSEMbLING THE cLEANER ATTAcH DUST bIN TO VAcUUM Fit the groove located on the lower front side of the Dust Bin to the hook located on the vacuum body and attach the hook located on the Dust Bin Handle to the vacuum body as shown. ATTAcH VAcUUM HOSE AND TOOLS 1. Attach the Twist Snap Hose by lining up the taps on the base with the corresponding notches on the back of the vacuum as shown. Turn the Twist Snap Hose clockwise to lock the hose into place. Grasping the Hose Wand, slide the end of the it onto the Hose Wand Base. Snap the Hose into the Hose Clip. Note: The vacuum will not operate effectively unless the Hose Wand is firmly attached. 4. Attach the Lower Cord Wrap by lining up the tab on the base with the corresponding notch on the back of the vacuum and turn it clockwise as shown. Attach the Extension Wand and the Crevice Tool together into the holder on the right side of the body as shown. Attach the Combination Tool into the holder on the left side of the body as shown. Attach the Bracket Brush on the front of the handle and clip the Mini Turbo Brush into the Bracket Brush as shown. * Select Models Only assembling the cleaner _7 Operating the cleaner pOwER SwITcH The Power Switch is located on the side of the vacuum. Push the rocker switch "ON" to vacuum, and "OFF" when cleaning is complete. HANDLE pOSITIONS Press the handle release pedal, located on the lower left side of the vacuum, with your foot to place your vacuum into one of three cleaning positions. 1. Upright ­ For storage and above floor cleaning with tools. 2. Low Cleaning ­ Press handle release pedal once. Position used for most household floor cleaning tasks. ­ With the vacuum in normal cleaning position, press handle release pedal again. Use for reaching under low furniture such as tables, chairs or beds. HEIGHT ADjUSTMENT The Powerfoot/Rotating Floor Brush can be adjusted to clean several floor surfaces. Note : For optimal cleaning performance, adjust to the lowest practical setting. If your cleaner is difficult to push, adjust to the next higher setting. Always ensure that the correct height setting is used for your flooring type as damage may occur if the height setting is not changed to reflect your flooring type. Turn Height Adjustment Knob to desired setting. Bare floor Setting ­ For bare floors. Medium Settings Highest Setting ­ For short and medium pile carpets. ­ For plush pile carpet TRANSpORTING cLEANER 1. To move your cleaner from room to room, put the Handle in the upright position, tilt the cleaner back on its rear wheels and push forward. The cleaner can also be moved by using the Carrying Handle located on the top of the Dust Bin. Carrying Handle 8_ operating the cleaner Operating the cleaner SpEcIAL ON-bOARD TOOLS Your vacuum is not only a powerful carpet and rug cleaner, it's also a versatile above floor vacuum cleaner when you select one of the special tools. [. . . ] Grasp turbine and pull firmly to remove. Remove a screw, and lift the cover belt off. With flat sides of turbine retainers pointing down, slide retainers into grooves in tool housing and snap into place. Replace brushbar and bottom plate. cleaning brushbar · Cut off pet hairs or threads surrounding brush with scissors. maintenance _13 Troubleshooting Check this list of possible problems and solutions before bringing your vacuum to a service center. PROBLEM Vacuum cleaner won't run · Power cord not plugged in · Blown fuse/tripped breaker in home possible solution · Check electrical plug · Check/ Replace fuse or reset breaker Vacuum cleaner and tools won't pick up dirt · Incorrect Height Adjustment · Hose not attached to suction opening · Twist Snap Hose not securely attached · Crack or hole in Hose · Broken or worn Drive Belt · Rotating Floor Brush bristles worn · Rotating Floor Brush jammed · Clog in vacuum · Dust Bin full · Dust Bin not installed properly · Filters are dirty · Mini Turbo Brush is clogged or debris is wrapped around the brush roll Visible dirt escaping from cleaner · Dust Bin full · Filters missing or installed incorrectly · Dust Bin installed incorrectly · Empty Dust Bin · Check Pre-motor and Post-motor filters for correct installation · Pull out and re-attach Dust Bin correctly · Adjust Powerfoot to correct height setting · Firmly push Hose Wand onto the suction opening · Make sure Twist Snap Hose is snapped into locked position. [. . . ]