User manual SAMSUNG SU4341

[. . . ] ·Donothandlevacuumcleanerorplugwithwethands. · onotputanyobjectintoopenings. Donotusewithanyopeningblocked;keepopenings D free of dust, lint, hair and anything that may reduce air flow. ·Keephair, looseclothing, fingersandallpartsofbodyawayfromopeningsandmovingparts. ·do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes. [. . . ] · Use upholstery side for curtains, draperies, cushions, fabrics. Crevice tool: Use in corners, on stairs, baseboards, and behind furniture. Extension Wand: Use with desired attachments and narrow wand for a longer reach. Mini Turbo Brush : Use rotating brush action for small areas such as stairs and upholstery. Note: Press gently when using Mini Turbo Brush to gain maximum cleaning. Too much pressure could cause the brush to stop rotating. Wooden Floor Brush (Select Models): Use for bare floors. Swivel head turns to get into tight spaces and fits under cabinets. Note: The Wooden Floor Brush does not store on board. B C Carrying handle The cleaner can also be moved by using the carrying handle. D option E Cleaning Tool attachments Attachment tools can be used to clean furniture or drapes, on stairs or in corners. When using the attachments, ensure the vacuum cleaner is placed firmly on the floor with the handle in the upright position. do not place the vacuum on top of furniture or steps as the brushroller may cause damage. 2-6 2-7 BARE FLO OR HIG H CARP ET 2-8 BARE FLOOR HIGH CARPET Cleaning lightweight flexible rugs Stand on one end of rug and move cleaner toward other end or edge. before reaching edge, push down on handle. This will lift up the nozzle(frontofcleaner)andwill prevent rug from clinging to cleaner. Continue to lift front of cleaner so that when you have reached the edge, it is completely off the rug. Move cleaner back to start again, lower front of cleaner, and use only forward strokes. Height adjustment 1. urnheightadjustmentdial(A)todesiredsetting. T bare Floor : For no-carpeted, bare floors. Medium Setting : For short and medium pile carpets. highest Setting : For plush pile carpet. Note : For optimal cleaning performance, adjust to the lowest practical setting. Ifyourcleanerisdifficulttopush, adjusttothenexthighersetting. Always ensure that the correct height setting is used for your flooring type as damage may occur if the height setting is not changed to reflect your flooring type. 6 O per ation CAUTION When using the hose attachment, please ensure that vacuum remains flat and level on the floor surface to prevent contact from the brush roller with the floor surface. [. . . ] Shouldtheagitatorshield(D) become dislodged while replacing the belt or the agitator, reposition it as shown, noting the placement of itsbeltguide(E) grasp agitator firmly and fit it into position by first sliding the end opposite the belt into the rectangular slot(F)onsideofcleaner. Pivot bottom plate down and snap closed. 3-20 3-21 3-22 Belt Replacement grasp turbine and pull firmly to remove. Replace with new belt. With flat sides of turbine retainers pointing down, slide retainers into grooves in tool housing and snap into place. Replace brushbar and bottom plate. Cleaning Brushbar · utoffpethairsorthreads C surrounding brush by using scissors. 10 Tro ub lesho oting Check this list of possible problems and solutions before bringing your vacuum to a service center. Problem: Cleaner won't run Possible Cause Possible Solution · Not firmly plugged in · Plug unit in firmly · No voltage in wall plug · Check fuse or breaker · Blown fuse or tripped breaker · Replace fuse or reset breaker · Filters blocked or dirty · Clean filters as per manual instructions Problem : Poor job of dirt pickup Possible Cause Possible Solution · Full or clogged Dirt Cup · Empty the Dirt Cup and check for blockages. [. . . ]