User manual SAMSUNG SV-243B INTRODUCTION (VER.1.0)

[. . . ] VIDEO CASSETTE RECORDER SV-245B SV-243B SV-240B Instruction Manual www. samsungvcr. com PAL Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. REFER TO QUALIFIED SERVICE PERSONNEL. DANGER This symbol is intended to alert you to the presence of dangerous voltage within the product. IMPORTANT NOTE The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug. [. . . ] An index is recorded on the tape (see page 32). x If your VCR ejects the cassette when you start recording, check to make sure that the cassette's safety tab is intact or that the opening (created by a broken safety tab) is covered with adhesive tape. x If you reach the end of the tape while recording, the cassette rewinds automatically. 7 6 MENU 7 22 Using the VIDEOPLUS+ Feature 5(SV-245B/SV-243B Only) GB Before presetting your VCR: x Switch on both the television and your VCR x Check that the date and time are correct SPEED DUB TV/VCR TIMER x Insert the cassette on which the programme is to be recorded (safety tab intact) Up to six programmes can be preset. 1 1 2 ** TIMER METHOD ** STANDARD VIDEOPLUS Press the TIMER button. Press the corresponding option is selected. $ or buttons, until the VIDEOPLUS 3 Press the !button to select VIDEOPLUS. A message is displayed to allow you to enter the Result: VIDEOPLUS+ code. $ END: MENU If all six programmes have been set, the message TIMER IS FULL is displayed. Refer to page 27 if you wish to cancel a preset recording. 4 VIDEOPLUS CODE --------- Press the numeric buttons to enter the code opposite the programme that you wish to record in your television magazine. If you wish to correct the VIDEOPLUS+ code that you are entering: x Press the button until the digit to be corrected is cleared x Enter the correct digit CODE:0-9 CORRECT: END:MENU 5 Press the MENU button. The information concerning the programme is displayed. Result: PROG PR 1 -----$ DAY MO 1 --------------- 1/JAN MON 21:28 V/P STARTSTOP 12:0012:50SP ON --:----:---- --:----:---- --:----:---- --:----:---- --:----:---- MENU When using the VIDEOPLUS+ function for the first time with stored stations, the programme number flashes. This one time, you must enter the station number manually by pressing the $ or buttons. Refer to the following page if: x The programme number or times flash x You wish to modify the programme 6 7 8 If the programme and times are correct, press the MENU button. Press the VCR STANDBY/ON (STANDBY/ON) button to activate the timer. Refer to page 27 if you wish to: x Check that your VCR has been programmed correctly x Cancel a preset recording DELETE:CLR/RST 5(SV-245B) 5(SV-243B) VCR STANDBY/ON STANDBY/ON 7 7 The numbers next to each TV programme listing are VIDEOPLUS+ code numbers, which allow you to programme your videorecorder instantly with the remote control. Tap in the VIDEOPLUS+ code for the programme you wish to record. SH SH TM VIDEOPLUS+ is a trademark of Gemstar Development Corporation. The VIDEOPLUS+ system is manufactured under licence from Gemstar Development Corporation. 24 Using the Timer Programming Feature GB 5(SV-245B/SV-243B) The Timer Programming feature allows you to preset the VCR to record a programme up to one month before that programme is to be broadcast. Up to six programmes can be preset. ** TIMER METHOD ** STANDARD VIDEOPLUS Before presetting a recording, check that the date and time are correct. 1 $ END: MENU - Insert the cassette and press the TIMER button. Press the $ or buttons to select the STANDARD option and then press the !button or, x Press MENU on the remote control. Result: The programming menu is displayed. x Press the OK button to select TIMER PROGRAMMING option. Result: The TIMER PROGRAMMING menu is displayed. Select the required station by pressing the $, buttons or INPUT to select the AV1 input sources. Select the required day by pressing the $ or buttons. Press to select the recording start time. [. . . ] If there was a power failure or interruption during timer recording, the recording will have been cancelled. Check to see if you are using a prerecorded tape. Press the PROG/TRK ($ or ) / TRK ( minimize this effect. or ) buttons to You cannot insert a video cassette The television programme was not recorded x x x x x x x Timer recording was unsuccessful No playback picture or the picture is distorted You cannot see normal broadcasts x x x Noise bars or streaks on playback When the II button is pressed during playback, the still picture has severe "noise bars" streaks Video Head Cleaning x x x A still picture may have "noise bars", depending on the condition of the tape. [. . . ]