User manual SAMSUNG SW68ASP

[. . . ] WASHING MACHINE SW68ASP / SW57APP User's Manual Please read this manual before using and note how to use in the proper manner. Please be careful of keeping the manual. Otherwise, it should be bought separately. The User's Manual is for common use. [. . . ] - The product warranty does not cover problems resulting from disassembling the product. · Do not use this product for business purposes. · For washing machines with ventilation openings in the base, that a carpet must not obstruct the openings. 3 SW68ASP-02290A-EN. indd 3 2006-08-21 ¿ÀÈÄ 8:33:08 INSTALLATION & MAINTENANCE ENVIRONMENT Leave some space. Maintain at least 10cm between the washer and the wall. IN CASE OF PUMP-DRAINED WASHER ake out the Be sure to join tightly Install the drain T cap-hose and the drain hose into the hose in the position connect the drain-outlet on the left of about 70~80cm outlet-hose above the ground. side of the machine. Place the washer on a sturdy flat surface. If the washer is placed on an uneven or weak surface, noise and vibration can occur (allowable slope is 1 degree) Never install the washer in a very steamy environment or where it might be open to the rain. Excessive moisture may cause an electrical shock hazard. Avoid direct sunlight or heaters. As plastic and electrical components are affected by direct heat, never place the washer near furnaces, boilers, etc. Do not place under direct sunlight. HOW TO CONNECT WATER SUPPLY HOSE Check the type of tap fitting which is in your laundry and then see appropriate instruction below: A tap of ordinary type is desirable In case of square tap ake out the internal part of the connector T and join it in the following way. Internal part ORDINARY TAP SQUARE TAP 1. Remove the adaptor from the water supply hose. ROTATING TAP 4. Connect the water supply hose to the adaptor. Pull down the part (c) of the water supply hose . When you release part (c) the hose is automatically connects to the adaptor making a 'click' sound. Connect the other end of the water supply hose to the inlet water valve at the top of the washer. Screw the hose clockwise all the way in. 2. First, using a "+" type screw driver, loosen the four screws on the adaptor. Next, take the adaptor and turn part(b) following the arrow for gap about 5mm between them. Connect adaptor to the water tap by tightening the screws firmly. Then, turn part (b) following the arrow and put (a) and (b)together. 6. If the water tap is a screw type, assemble a water supply hose that fits to the tap as shown. Note : The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not be used. 4 SW68ASP-02290A-EN. indd 4 2006-08-21 ¿ÀÈÄ 8:33:11 HOW TO CLEAN THE FILTER Clean the filter net often to keep the washer clean. CLEANING THE FILTER (pump drained washer) 1. Place a rag under washer filter not to wet the floor. Take out the filter and remove any sludge. Close the cover and part of the filter as shown in the insert the lower part and pull in. of the filter in the basket first and then push the filter with "click" sound . HOW TO ADD THE DETERGENT 1. Open the detergent box by pulling in the direction of the arrow as shown in the figure. Add the amount of detergent for one washing evenly in the box so that the detergent does not overflow the box. LEVELLING 1. Pull down the adjusting handles of the adjusting feet which are located at the right and left of the front side. Adjust the height of the machine upwards or downwards. [. . . ] Unplug the power cord after washing. SPIN ONLY When you choose this cycle, only spin cycle is operated. Pressing cycle key during spinning only cycle changes the spin dry time. The spin dry time can be changed to between 1 and 7 minutes. Unplug the power cord after washing. DELAY START This function allows you to delay the start of your chosen wash program for 3, 4, . . . [. . . ]