User manual SAMSUNG SWT70B1P

[. . . ] This is used to set the Washing/Rinsing or draining. Connect water inlet to a tap with a suitable hose. (For SWT70B1, SWT75A1) 3. CYCLE SELECTOR 6. WATER SELECTOR During washing, WATER SELECTOR KNOB should be selected to wash. During spin rinsing, WATER SELECTOR KNOB should be selected to spin. SWT70B1 SWT70A1 2 SWT75A1 WASHING PROCEDURE TO WASH 1. Before starting washing, check following; Connect the water supply hose. - Lay the drain hose down toward a sinkhole. [. . . ] RINSE WASH WASH TIMER DRAIN RINSE DRAIN 5. Set the CYCLE SELECTOR KNOB to `DRAIN'. DRAIN CYCLE SELECTOR CYCLE SELECTOR (in case drain pump "WASH) CYCLE SELECTOR 3. Supply the proper amount of water as not to overflow the top of the washing tub. 6. Repeat this cycle until drain water is clean. (2~3 cycle) OVER FLOW RINSE 1. Keep suppling water(adjust water pressure to ensure that the amount of water supplied does not exceed that water drained. ) WASH . RINSE WASH 3. As soon as the WASH TIMER shuts off, turn off the water tap. DRAIN RINSE DRAIN CYCLE SELECTOR CYCLE SELECTOR (in case drain pump "WASH) WASH TIMER 2. Set the WASH TIMER 6~8minutes. 4. Set the CYCLE SELECTOR KNOB to `DRAIN'. DRAIN CYCLE SELECTOR WASH TIMER ADDITIONAL RINSE (SHOWER RINSE FOR SWT70B1, SWT75A1) for more 1 courseselect onlyeffective rinse (Don't this course for rinse. ) Load the laundry evenly into the spin basket. After rinsing you can select this 4 supply, cover the After stopping water laundry with safety cover safety cover and close the inner lid. inner lid 2 Set the WATER SELECTOR KNOB to SPIN for 5 Close the spin dryer lid. SWT70B1, and CYCLE SELECTOR KNOB to `DRAIN'. WASH SPIN DRAIN CYCLE SELECTOR water for about 1minute. 3 Supplythe water flow to prevent Adjust overflow from the wash tub. DRY 6 Set the SPINminutes. TIMER 2~3 SPIN DRY TIMER 4 INSTALLATION ENVIRONMENT Leave some space Space at least 15cm between the washer and the wall. CHANGING THE POSITION OF THE DRAIN HOSE Before attempting to change the position of the drain hose, disconnect the plug from the outlet. Route the drain hose inside the machine. 2. Take out the drain hose from the opposite hole and insert the drain hose into the hose holder. Place the washer on a sturdy flat surface. If the washer is placed on an uneven or weak surface, noise or vibration may be occured. (Allowable is 2°) Never install the washer near water. Do not place the washer in steamy rooms or where the washer is directly exposed to rain. Moisture may destroy the electrical insulation and cause an electrical shock hazard. 1 2 Hose holder Avoid direct sunlight or heating devices. As plastic and electrical components are affected by direct heat, never place the washer near heaters, boilers, etc. Do not place under direct sunlight. HOW TO CLEAN THE FILTER (In case drain pump) 1. Place a rag under the washer filter not to wet the floor. Rotate the filter counterclockwise and pull out the filter. Remove dirts and rotate the filter clockwise until it Open locks in position. 70~80cm Install the drain hose about 70~80cm above the ground for pump model. Filter Close Rag CLEANING THE MACHINE CLENING THE LINT FILTER -If the dregs are piled up in the lint filter after finishing the wash, push down and pull it out as shown in figure. -Wash the filter net in water. CLEANING THE WASH TUB Wipe off strains on the cabinet and operation panel with soft cloth. Do not use benzene, thinners, cleanser, or wax, nor scrub the washer with a brush. [. . . ] Expand the concave and convex parts, and pull up the spin dryer hatch to remove it. Push in hatch firmly until the catch at the front is engaged securely. TROUBLE SHOOTING TROUBLE The washer does not work. CHECK POINT Check that the power cord is connected to a power outlet well. Power stoppage? TROUBLE Incomplete draining CHECK POINT Is the filter clogged with lint?q See "Cleaning the machine" on page 5. Clothes will not move freely. [. . . ]