User manual SAMSUNG SYNCMASTER 997DF

[. . . ] SyncMaster 591S/793S/591V/793V/783DF/793DF /795DF/797DF/997DF/793MB/795MB Main Page On-Screen Display Safety Instructions Notational Power Installation Clean Other Troubleshooting Check List Q&A Self-Test Feature Check Introduction Unpacking Front Rear Bottom Specifications General Specifications PowerSaver Preset Timing Modes Setup Connecting Your Monitor Installing the Monitor Driver Automatic Manual Base Installation Information Service Terms Regulatory Natural Color Authority Notational Power Installation Clean Others Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock When not used for extended periods of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode. Notational Power Installation Clean Others If the size of your monitor is small, or if the same image is present for long periods of time, you may see afterimages due to damage to the fluorescent substance on the inside of the CDT. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. [. . . ] If the program runs on Windows XP, go to [Control Panel] in the [Start] menu. Click the "Add or Remove Programs" icon in Control Panel. In the "Add or Remove Programs" screen, sc roll down to find "Magic Tune. " Clic k on it to highlight it. Click the "Change/Remove" button to remove the program. Click "Yes" to begin the uninstall process. Wait until the "Uninstall Complete" dialog box appears . Visit the MagicTune website for technical support for MagicTune, FAQs (questions and answers) and software upgrades. Overview | Installation | OSD Mode | Uninstall | Troubleshooting Troubleshooting MagicTune may not work in case monitor is replaced or driver of graphic card is updated while MagicTune is operating. If so, please restart the system. Check when MagicTune does not function properly. * MagicTune feature is found only on PC (VGA) with Window OS that supports Plug and Play. * To check whether your PC is available for MagicTune feature, follow the steps below (When Windows is XP); Control Panel -> Performance and Maintenance -> System -> Hardware -> Device Manager -> Monitors -> After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching new Hardware. Visit the MagicTune website for technical support for MagicTune, FAQs (questions and answers) and software upgrades. Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call, the phone number on the Information section or contact your dealer. Check List Q&A Self-Test Feature Check Symptom No images on the screen. I cannot turn on the monitor. Check List Is the power cord connected properly?" on the Solutions Check the power cord connection and supply. Check the signal cable connection. If the power is on, reboot the computer to see the initial screen(the login screen), which can be seen. If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card. (Refer to the Preset Timing Modes) Note: If the initial screen (the login screen) does not appear, contact a service center or your dealer. Can you see " screen? " on the You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. Adjust the maximum resolution and frequency that the monitor can handle properly. There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode. Press any key on the keyboard or move the mouse to activate the monitor and restore the image on the screen. The signal from the video card exceeds the maximum resolution and frequency of the monitor. The image on the screen is shaking. Check the monitor configuration to see if it is in Interlace Mode. (Interlace Mode: Vertical frequency 43Hz, 87Hz(i), etc) Are there any magnetic products such as a power adapter, speaker or a high voltage wire near by?Is the voltage stable? Move the monitor away from anything that can create a strong magnetic field. The screen image can appear to shake or vibrate at a particular time of day due to low supply voltage. The screen image can also appear to shake or vibrate if there is a problem with the video card or the computer's main board. [. . . ] Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction. Our labelling system started with displays in 1992 and is now requested by users and IT-manufacturers all over the world. For more information, Please visit www. tcodevelopment. com TCO'03 Recycling Information (TCO'03 applied model only) [European Residents Only] For recycling information for TCO'03 certified monitors, for the residents in the following countries, please contact the company corresponding to your region of residence. For those who reside in other countries, please contact a nearest local Samsung dealer for recycling information for the products to be treated in environmentally acceptable way. [. . . ]