User manual SAMSUNG TX-M2792F OWNER'S MANUAL (VER.1.0)

[. . . ] TXM2792F TXL2767 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Owner's Instructions AA68-02477B-00 (ENG) COLOR TELEVISION Warning!Important Safety Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside. [. . . ] The TV will change channels when you press the second number. When you use the number buttons, you can directly select channels that were either erased or not memorized. To select a channel over 100, press the +100 button. (For channel 122, press "+100", then "2", then "2". ) To change to single-digit channels (0­9) faster, press "0" before the single digit. (For channel "4", press "0", then "4". ) Using the PRE-CH Button to select the Previous Channel 1 Press the PRE-CH button. The TV will switch to the last channel viewed. To quickly switch between two channels that are far apart, tune to one channel, then use the number button to select the second channel. Then, use the PRE-CH button to quickly alternate between them. w Adjusting the Volume Press the VOL + or VOL­ button to increase or decrease the volume. Using Mute At any time, you can temporarily cut off the sound using the Mute button. 1 Press the MUTE button and the sound cuts off. The word "Mute" will appear in the lower-left corner of the screen. 2 To turn mute off, press the MUTE button again, or simply press either the VOL ­ or VOL + button. 3. 8 CHAPTER THREE: TV OPERATION O P E R AT I O N Labeling the Channels Use this feature to assign an easy-to-remember label to any channel (i. e. , "CBS", "ESPN", "PBS2", CNN1", etc. ) A label consists of four fields, where each field is a letter, a number, "*", or a blank. When the DISPLAY button is pressed, the channel label will appear next to the channel number. 1 Press the CH v or CH w button to tune to the channel that will be labeled. 2 Press the MENU button to display the menu, then press the CH w button to select "Channel". Labeling : ---- Note: You cannot select "Labeling" in the A/V mode. w Press the VOL + button. 3 Press the CH w button to select "Labeling". Press the VOL + button to begin labeling. The left-most field will be highlighted. See top paragraph. ) Labeling : ---- 4 Press the CH v or CH w button to select a letter, a number, "*", or a blank. (Pressing the CH v button results in this sequence: A, B, . . . Z, *, blank, 0, 1, . . . 9). 5 Press the VOL+ button to switch to the next field, which will be highlighted. Select a second letter or digit using the CH v and CH w buttons, as above. Repeat the process to select the last two digits. Labeling : CNN1 Press the MENU button to set the label and clear the menus from the screen. CHAPTER THREE: TV OPERATION 3. 9 O P E R AT I O N Setting the Clock 1 Press the MENU button to display the on-screen menu. Press the CH w button three times to select "Function". Press the VOL + button. Plug & Play 2 Press the CH w button to select "Time" menu. Press the VOL + button: The Time menu will appear on the screen, and "Clock" will be selected. Plug & Play 3 Press the VOL + button again (the hours digits will be selected). Press the CH v or CH w button repeatedly until the correct hour appears. After the hour is entered, press the VOL + button. (at this point the minutes digits will be selected. ) When selecting the hours, be sure to select the proper time of day (AM or PM). You can change the hours by pressing CH v or CH w repeatedly (or by holding down either of these buttons). w w 4 Press the CH v or CH w button to select the correct minutes. After selecting the correct minutes, press the VOL + button. [. . . ] Note: The V-Chip will automatically block any category that is "more restrictive. " For example, if you block the "PG-13" category, then "R, " "NC-17, " and "X" will automatically be blocked also. How to Reset the TV after the V-Chip Blocks a Channel ("Emergency Escape") If the TV is tuned to a restricted channel, the V-Chip will block it. The screen will go blank and the following message will appear: "Excessive rating". To resume normal viewing, tune to a different channel using the number buttons. Under certain conditions (depending on the rating of the local TV programs) the V-Chip might lock out all the channels. [. . . ]