User manual SAMSUNG TX-N2020 INTRODUCTION (VER.1.0)

[. . . ] TXN1430F / TXN1634F TXN2022 COLOR TELEVISION . . . . . . . . . . . . . Owner's Instructions Printed in Mexico AA68-02833A (ENG) Warning!Important Safety Instructions CAUTION RISKOFELECTRICSHOCK DONOTOPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside. [. . . ] Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected. Proceed to "Storing Channels in Memory" (next page). 3 Press MENU twice to exit. CHAPTER THREE: TV OPERATION 3. 3 O P E R AT I O N Storing Channels in Memory (Automatic Method) 1 First, select the correct signal source (ANT, STD, HRC, IRC). Press the MENU button, then press the CH w button twice to select "Channel, " then press the VOL + button. 2 Press the CH w button to select "Auto program". 3 Press the VOL + button. The TV will begin memorizing all of the available channels. The TV automatically cycles through all of the available channels and stores them in memory. Press the MENU button at any time to interrupt the memorization process and return to the Channel menu. 4 After all the available channels are stored, the Auto program menu reappears. Press the MENU button twice to exit. 3. 4 CHAPTER THREE: TV OPERATION O P E R AT I O N Adding and Erasing Channels (Manual Method) 1 Press the MENU button. Press the CH w button twice to select "Channel", then press the VOL+ button. 2 Press the CH v or CH w button to select "Add/Erase". Press the VOL+ button. 3 Press the VOL-/+ or number buttons to select the channel you want to add or erase. 4 Press the CH v or CH w button to select "Select". Press the VOL+ or VOLbutton to select "Added" or "Erased". Press the MENU button three times to exit. CHAPTER THREE: TV OPERATION 3. 5 O P E R AT I O N Changing Channels Using the Channel Buttons 1 Press the CH v or CH w button to change channels. When you press CH v or CH w, the TV changes channels in sequence. You will see all the channels that the TV has memorized. (The TV must have memorized at least three channels. ) You will not see channels that were either erased or not memorized. Directly Accessing Channels Use the number buttons to quickly tune to any channel. 1 Press the number buttons to go directly to a channel. For example, to select channel 27, press "2, " then "7. " The TV will change channels when you press the second number. When you use the number buttons, you can directly select channels that were either erased or not memorized. To select a channel over 100, press the +100 button. (For channel 122, press "+100, " then "2, " then "2. ") To change to single-digit channels (0­9) faster, press "0" before the single digit. (For channel "4, " press "0, " then "4. ") Using the PRE-CH Button to select the Previous Channel 1 Press the PRE-CH button. The TV will switch to the last channel viewed. To quickly switch between two channels that are far apart, tune to one channel, then use the number button to select the second channel. Then, use the PRE-CH button to quickly alternate between them. Adjusting the Volume Press the VOL + or VOL­ button to increase or decrease the volume. Using Mute At any time, you can temporarily cut off the sound using the Mute button. 1 Press the MUTE button and the sound cuts off. The word "Mute" will appear in the lower-left corner of the screen. 2 To turn mute off, press the MUTE button again, or simply press either the VOL ­ or VOL + button. 3. 6 CHAPTER THREE: TV OPERATION O P E R AT I O N Setting the Clock 1 Press the MENU button to display the on-screen menu. Press the CH w button three times to select "Function". Press the VOL + button. 2 Press the CH w button to select the "Time" menu. [. . . ] Press MENU four times to save the settings and to clear all screens. Note: The V-Chip will automatically block any category that is "more restrictive. " For example, if you block the "PG-13" category, then "R, " "NC-17, " and "X" will automatically be blocked also. How to Reset the TV after the V-Chip Blocks a Channel ("Emergency Escape") If the TV is tuned to a restricted channel, the V-Chip will block it. The screen will go blank and the following message will appear: "Excessive rating. " To resume normal viewing, tune to a different channel using the number buttons. Under certain conditions (depending on the rating of the local TV programs) the V-Chip might lock out all the channels. [. . . ]