User manual SAMSUNG TX-N3235F

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product. This symbol alerts you that important literature concerning operation and maintenance has been included with this product. Note to CATV system installer: This reminder is provided to call CATV system installer's attention to Article 820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. [. . . ] Press the MENU button. 4 Press the CH v or CH w button to select "Select". Press the VOL+ or VOLbutton to select "Added" or "Erased". Press the MENU button to exit. 3. 7 CHAPTER THREE: TV OPERATION O P E R AT I O N Changing Channels Using the Channel Buttons 1 Press the CH v or CH w button to change channels. When you press CH v or CH w, the TV changes channels in sequence. You will see all the channels that the TV has memorized. (The TV must have memorized at least three channels. ) You will not see channels that were either erased or not memorized. Directly Accessing Channels Use the number buttons to quickly tune to any channel. 1 Press the number buttons to go directly to a channel. For example, to select channel 27, press "2, " then "7. " The TV will change channels when you press the second number. When you use the number buttons, you can directly select channels that were either erased or not memorized. To select a channel over 100, press the +100 button. (For channel 122, press "+100, " then "2, " then "2. ") To change to single-digit channels (0­9) faster, press "0" before the single digit. (For channel "4, " press "0, " then "4. ") Using the PRE-CH Button to select the Previous Channel 1 Press the PRE-CH button. The TV will switch to the last channel viewed. To quickly switch between two channels that are far apart, tune to one channel, then use the number button to select the second channel. Press the CH v and CH w to select your local PBS channel. Press the MENU button. continued. . . 3. 11 CHAPTER THREE: TV OPERATION O P E R AT I O N 5 Press the CH w button to select "Time zone". While "Time zone" is selected, then press the VOL+ or VOL- to change the Time zone. Sequence: ATL. , EAST, CEN. , MTN. , PAC. , ALAS. , HAW. 6 Press the CH w button to select "DST"(Daylight saving time). While "DST" is selected, press the VOL+ or VOL- button to indicate "Yes" or "No". Press the MENU button to exit. CHAPTER THREE: TV OPERATION 3. 12 O P E R AT I O N Customizing the Picture You can use the on-screen menus to change the Contrast, Brightness, Sharpness, Color, Tint and according to personal preference. (Alternatively, you can use one of the "automatic" settings. See next page. ) 1 Press the MENU button to display menu. 2 Press the VOL ­ or VOL + button repeatedly, until the word "Custom" is selected. (When Custom is highlighted, the words "Adjust" will appear on the screen. ) 3 Press the CH w button to select "Adjust", then press the VOL+ button. (The words Contrast, Brightness, Sharpness, Color, and Tint will appear on the screen. ) Press the CH v or CH w button to select a particular item. 4 Press the VOL ­ or VOL + button to increase or decrease the value of a particular item. For example, if you select "Brightness, " pressing the VOL + button increases it. [. . . ] Press the CH v or CH w button to select "U" or"B". Press the MENU button to save the settings and to clear all screens. How to Reset the TV after the V-Chip Blocks a Channel ("Emergency Escape") If the TV is tuned to a restricted channel, the V-Chip will block it. The screen will go blank and the following message will appear: "Excessive rating. " To resume normal viewing, tune to a different channel using the number buttons. Under certain conditions (depending on the rating of the local TV programs) the V-Chip might lock out all the channels. [. . . ]