User manual SAMSUNG USP09WHWD2

[. . . ] OWNER'S INSTRUCTIONS Indoor unit ASK09WHWD ASK09WHWE ASK09WZWE ASK12WHWE ASK12WZWD ASK13WZWD ASP09SHWD ASP09WHWB ASP09WHWD ASP09WHWDL ASP09WHWE ASP09WOWE ASP09WZWES ASP12SZWD ASP12WHWB ASP12WHWE ASP12WZWD ASP13WZWD ASP13WZWE Outdoor unit USK09WHWD USK09WHWE USK09WZWE USK12WHWE USK12WZWD USK13WZWD USP09SHWD USP09WHWB USP09WHWD USP09WHWDL USP09WHWE USP09WOWE USP09WZWES USP12SZWD USP12WHWB USP12WHWE USP12WZWD USP13WZWD USP13WZWE SPLIT-TYPE ROOM AIR CONDITIONER ( Cooling ) E DB98-24361A(1) Register your product at www. samsung. com/global/register Safety Precautions The following safety precautions must be taken when using your air conditioner. · Disconnect all remote electric power supplies before servicing, installing or cleaning. · This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. x Users of this product are cautioned not to attempt repair of this product at their own discretion. [. . . ] Possible temperatures are between 16°C and 30°C inclusive. Result: x Each time you press the button: - The temperature is adjusted by 1°C - The indoor unit beeps x The air conditioner starts removing the excess humidity; the quantity of air is adjusted automatically. 4 To control the direction of the air flow, refer to page 15. E-11 Airing Your Room If the atmosphere in your room is stale, you can air the room using the Fan feature. 1 If necessary, press the Result: button. x The operation indicator on the indoor unit lights up. x The air conditioner starts up in the mode selected when the unit was last used. 1 If necessary, press the Result: button. x The operation indicator on the indoor unit lights up. x The air conditioner starts up in the mode selected when the unit was last used. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped lt will start up normally after three minutes. IMPORTANT 2 Press the Result: x x x x button. The air conditioner runs in the Energy saving mode. The outer air flow blade moves up and down. To stop the Energy saving mode, press the again. Note You can select the Energy saving mode only in the Cool mode. 3 To adjust the temperature, press the button one or more times until the required temperature is displayed. 4 To select the fan speed, press the the required setting is displayed. button one or more times until 5 To control the direction of the air flow, refer to page 15. E-14 Adjusting the Air Flow Direction Vertically Depending on the position of the indoor unit on the wall of your room, you can adjust the position of the outer air flow blade on the bottom of the unit, thus increasing the efficiency of the air conditioner. 1 Press the Result: button one or more times as required. The outer blade is adjusted vertically. 2 If you want the blade to move up and down automatically when the air conditioner is operating, press the button. Result: The blade move up and down, around the base position set. 3 To stop the blade moving up and down, press the button again. Note If you switch the air conditioner. . . Set to the initial position powered. Adjusting the Air Flow Direction Horizontally There are two sets of inner air flow blades. Just as the outer air flow blade can be adjusted vertically, the inner blades can be adjusted horizontally. 1 Adjust each set of inner blades to the required position, by pushing or pulling them sideways. E-15 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time. You can set the period of time from 1 hour to 24 hours. 1 To set the operating time, press the button one or more times until the required time is displayed. Possible time is between 1 hour and 24 hours inclusive. 2 Press the Result: button to complete the setting. x Blinking of the timer indicator stops. x The selected mode and the temperature on the display disappear after 10 seconds. x The air conditioner will switch on automatically when the counter displayed on the remote control reaches the set time and disappears the On Timer setting. 3 To select an operating mode in advance, press the button until the desired mode is displayed at the top of the remote control. [. . . ] x Check whether the Timer indicator on the indoor unit is switched on. If so: - Wait until the switch-on time is reached and the air conditioner starts up automatically - Cancel the timer (see pages 16 and 17 for further details) x Check that there are no obstacles between you and the indoor unit. x Check that you are close enough to the indoor unit (seven meters/ yards or less). x Check that you are pointing the remote control at the remote control sensor in the right of the indoor unit. [. . . ]