User manual SAMSUNG VC-6013V INTRODUCTION

[. . . ] It must not be used on people or animals. Never use your appliance to vacuum matches, glowing embers, or cigarette-ends. Avoid vacuuming hard, pointed objects, since they may damage the appliance or dust bag. [. . . ] Avoid vacuuming hard, pointed objects, since they may damage the appliance or dust bag. If your vacuum cleaner has a fault, please contact your electrical retailer or an auth-orized service agent. If the main cable is defective, the complete cable winder must be replaced by a service agent. PROTECTING THE ENVIRONMENT Once you have unpacked the unit, do not simply throw the packing into the household waste. Take them to the appropriate collecting points for recycling. 1 DJ68-00186H 0. 0 3/20/03 5:22 PM Page 3 IDENTIFICATIONS OF PARTS HANDLE AIR REGULATOR SUCTION HOSE TUBE* BUTTON FOR SUCTION HOSE REMOVAL CYCLONE FILTER* CARRYING HANDLE RUG/FLOOR SELECTOR DUST-FULL INDICATOR CORD REWIND BUTTON POWER CONTROL SWITCH* ON/OFF BUTTON FLOOR NOZZLE* CLAMPER FOR DUST BAG COMPARTMENT 1) Connect the suction hose to the cyclone filter. 3) Connect the suction tubes together (depending on model). 4) Connect the nozzle to the suction tube. v Features marked with * may vary according to model. ASSEMBLING THE VACUUM - CLEANER READY FOR USE 2) Connect the cyclone filter to the suction tube. OPTION : Adjusting the telescopic tube(depending on model). 5) Connect the body connector to the body of the cleaner. 2 DJ68-00186H 0. 0 3/20/03 5:22 PM Page 4 POWER CORD 1) PULLING OUT The power cord is long enough to be drawn out for convenience. 2) REWINDING When you have finished cleaning, disconnect the plug from the electrical outlet and simply press the cord rewind button lightly with your toe. NOTE : When removing the power cord from the electrical outlet, grasp the plug, not the cord. ON / OFF SWITCH With the cord plugged into an electrical outlet, start or stop the vacuum cleaner by pushing lightly downward on the switch with your toe. POWER CONTROL(VARIABLE CONTROL TYPE ONLY ) The vacuuming power can be adjusted to suit any situation with the electrical power control. M I N = For delicate fabrics, e. g. net curtains. MAX = For hard floors and heavily soiled carpets. 3 DJ68-00186H 0. 0 3/20/03 5:22 PM Page 5 DUST-FULL INDICATOR If the "Dust-Full" indicator changes to "RED" while you are cleaning, the dust bag requires replacement. NOTE : If the "Dust-Full" indicator continues to display "RED" even after changing the dust bag, turn the cleaner off and check whether the hose, tube or nozzle is clogged. CREVICE USING THE ACCESSORIES DUSTING · Crevice tool for radiators, crevice, corners, between cushions. · Dusting brush for furniture, shelves, books, etc. · Before use, assemble the dusting brush to the crevice tool. TOOL STORAGE Your cleaner features a tool storage device. Adjust indicating marks each other carved on Dust Barrel and Cyclonic Filter. CYCLONIC FILTER CREVICE DUST BARREL REPLACING THE DUST BAG TOOL 1) To open the dust cover of the dust bagcompartment, press the clamper upward. (The clamper is located at the front of the dust cover) 2) Remove the carrying bag from the cleaner. 5 DJ68-00186H 0. 0 3/20/03 5:22 PM Page 7 3) After removing the used dust bag, insert the cardboard bag collar of the new dust bag into the carrying bag. 4) Press the dust cover down gently until the clamper relocks. NOTE : Used dust bag can be sealed by removing the film from the paper and sticking the latter over the suction opening. (ONLY PAPER BAG) FOR CLOTH FILTER BAG After using, if the cloth filter bag is full of dust, clean the cloth filter bag and use it again. MAINTENANCE OR REPLACEMENT OF THE FILTERS 1) INLET-FILTER. · Open the dust cover. · After detaching the filter, wash it lightly withwater, dry it in the shade, and then insert it in its original position. · Close the dust cover. 2) OUTLET-FILTER. · To open the filter cover, press front and pull it simultaneously. · Remove and replace the dirty microfilter. 6 DJ68-00186H 0. 0 3/20/03 5:22 PM Page 8 USAGE OF FLOOR NOZZLE FOR RUG / FLOOR SELECTOR Before use make sure that the position of the selector is in the right position for the type of surface to be cleaned. Select the carpet indicator when cleaning carpets. . Select flat surface indicator when cleaning the floors, tiles, etc. [. . . ] · Remove and replace the dirty microfilter. 6 DJ68-00186H 0. 0 3/20/03 5:22 PM Page 8 USAGE OF FLOOR NOZZLE FOR RUG / FLOOR SELECTOR Before use make sure that the position of the selector is in the right position for the type of surface to be cleaned. Select the carpet indicator when cleaning carpets. . Select flat surface indicator when cleaning the floors, tiles, etc. [. . . ]