User manual SAMSUNG VC-8926EN

[. . . ] Close supervision is necessary when any appliance is used by or near children. Do not allow the vacuum cleaner to be used as a toy. Do not allow the vacuum cleaner to run unattended at any time. [. . . ] 1) For slider control types Slide the controller to upwards or downwards to adjust the power output. s Model with controller on the body of cleaner s Model with controller on the handle 2) For button control types Press (+)button to heighten the power. Press (-)button to lower the power. s Model with controller on the body of cleaner s Model with controller on the handle 4 DJ68-00093J 6/17/02 12:59 PM Page 6 AUTO MODE (BUTTON CONTROL TYPE ONLY) If you press AUTO MODE, the power is automatically set at 1200~1300 watt. This mode reduces the suction power fluctuation which is caused by the fluctuation of airflow quantity to the motor. For example, when dust bag is full, the quantity of air to the motor will be decreased and power will be down followingly. AUTO MODE, in this case, increases the power automatically for sufficient suction. If you want to go back to the normal control type, just press "+" or "-" buttons. Using Exbug Elimination System (DEPENDING ON MODEL) It is best to use the Mite Killing cycle immediately after you have finished your cleaning. Ensure machine is plugged in and the power point is switched on. Disconnect the hose from the cleaner by pressing in the two buttons on the hose end and lift the hose out. Close the hose connection cover on the top of the cleaner until tone is heard. Switch the cleaner on and the cleaner will run. The Mite Killer cycle will automatically stop when complete. Unplug the cleaner, rewind the cord, open the hoses connection cover and re-connect the hose. Your cleaner can be used immediately after the Mite Killer cycle stop or by interrupting the cycle. To do this, switch cleaner off, open the hose connection cover and re-connect the hose. 5 DJ68-00093J 6/17/02 12:59 PM Page 7 USING THE ACCESSORIES Open the tool storage cover upwards. CREVICE DUSTING UPHOLSTERY Crevice tool for radiators, crevices, corners, between cushions. Dusting brush for furniture, shelves, books, etc. Upholstery brush for cushions and drapery. PARK POSITION Located in the top rear side of the vacuum cleaner, there is a nozzle support that can be used to park the nozzle during pauses in cleaning TRANSPORTING AND STORING THE VACUUM CLEANER For easy storage and transportation, this vacuum cleaner has a clip system built into body, which will keep the wand, hose and nozzle in an upright position. 6 DJ68-00093J 6/17/02 12:59 PM Page 8 REPLACING THE DUST BAG 1) To open the dust cover of the dust bag compartment, press the clamper upwards(the clamper is located at the front of the dust cover). 2) Remove the dust bag from the cleaner 3) After removing the used dust bag, insert the cardboard bag collar of the new dust bag into its original position. 4) Press the dust cover down gently until the clamper relocks. NOTE : Used dust bags can be sealed by removing the film from the paper and sticking over the suction opening. FOR CLOTH FILTER BAG After using, if the cloth filter bag is full of dust, clean the cloth filter bag and use it again. DUST-FULL INDICATOR If the "Dust-Full" indicator switch changes to "RED" while you are cleaning, the dust bag is full and must be replaced. NOTE : If the "Dust-Full" indicator continues to display "RED" even after changing the dust bag, turn the cleaner off and check whether the hose, tube or nozzle is clogged. 7 DJ68-00093J 6/17/02 12:59 PM Page 9 CYCLONIC FILTER (ONLY CYCLONIC FILTER TYPES) You can use a dust bag in your cleaner for a long time thanks to the Cyclonic Filter system and it maintain the maximum cleaning efficiency. [. . . ] Remove the alien substance with a stick from it. After cleaning it, reassemble the nozzle to the tube. 10 DJ68-00093J 6/17/02 12:59 PM Page 12 TROUBLE SHOOTING PROBLEM Motor does not start. Filter, nozzle, suction hose or tube is blocked. [. . . ]