User manual SAMSUNG VC-8930E

[. . . ] Do not block the suction or the exhaustion part. Switch the vacuum cleaner off at the machine before unplugging from the electrical outlet. Grasp the plug to disconnect cord from electrical outlet before changing the dust bag. [. . . ] If your vacuum cleaner is not operating correctly, switch off the power supply and consult an authorized service agent. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. WARNING 1. The hose should be checked regularly and must not be used if damaged. 1 DJ68-00093N 5/30/02 9:20 AM Page 3 IDENTIFICATIONS OF PARTS REMOTE POWER CONTROL * (REMOTE CONTROL TYPE ONLY) HOSE * HANDLE * SUCTION REGULATOR * CYCLONIC FILTER * CORD REWIND BUTTON TRANSPARENT TUBE * AUTO BUTTON POWER CONTROL SWITCH * ON/OFF BUTTON TUBE * FLOOR NOZZLE * TOOL STORAGE COVER BUTTON FOR SUCTION HOSE REMOVAL DUST COVER CLAMPER FOR DUST BAG COMPARTMENT CARRYING HANDLE Features marked with * may vary according to model. w 2 DJ68-00093N 5/30/02 9:20 AM Page 4 ASSEMBLING THE VACUUM-CLEANER READY FOR USE 1) Connect the suction hose to the suction tube. 2) Adjust the suction tube(depending on model). x EXTENDING : Holding the narrow part of the telescopic tube with one hand, push the handle in the opposite direction with your other hand. SHORTENING : Holding the narrow part of the telescopic tube with one hand, pull the handle towards it using the other hand. OPTION NOTE : Adjustable telescopic tube is not available with all models. OPTION : Connect the suction tubes together. 3) Connect the nozzle to the suction tube. 4) Open the hose connection cover. 5) Connect the body connector to the body of the cleaner. 3 DJ68-00093N 5/30/02 9:20 AM Page 5 POWER CORD 1) PULLING OUT : The power cord is long enough to drawn out for convenience. 2) REWINDING : When you have finished cleaning, disconnect the plug from the electrical outlet and simply press the cord rewind button lightly with your toe. NOTE : When removing the power cord from the electrical outlet, grasp the plug, not the cord. ON/OFF SWITCH You can start or stop your vacuum cleaner by pressing the on/off switch lightly with your toe. POWER CONTROL(VARIABLE CONTROL TYPE ONLY) The vacuuming power can be adjusted to suit any situation with electrical power control. ECO = Economy setting for normally soiled carpets. MAX = For hard floors and heavily soiled carpets. 1) For slider control types Slide the controller to upwards or downwards to adjust the power output. s Model with controller on the body of cleaner s Model with controller on the handle 2) For button control types Press (+)button to heighten the power. Press (-)button to lower the power. s Model with controller on the body of cleaner s Model with controller on the handle 4 DJ68-00093N 5/30/02 9:20 AM Page 6 AUTO MODE (BUTTON CONTROL TYPE ONLY) If you press AUTO MODE, the power is automatically set at 1200~1300 watt. Disconnect the Cyclonic Filter from extension wand and handle. Remove thread and hair tangled around the net. After cleaning the Dust Barrel and Cyclonic Filter, connect the Cyclonic Filter with extension wand and handle(washed part should be dried in the shade throughly before assembling. ) 5. Push and turn the Dust Barrel to the right. Adjust indicating marks each other carved on Dust Barrel and Cyclonic Filter. CYCLONIC FILTER CREVICE TOOL DUST BARREL 8 DJ68-00093N 5/30/02 9:20 AM Page 10 MAINTENANCE OR REPLACEMENT OF THE FILTERS INLET FILTER v v The secondary filter, located behind the grille in the back of dust bag compartment, protects the motor from dirt particles. Do not allow the filter to become clogged. Suction power reduction or motor damage may result. If filter becomes dirty, pull off the grille and lift out filter. After cleaning the secondary filter attach it in place. NOTE : The filters must be completely dried before being replaced in the dust compartment. OUTLET FILTER For Micro Filter Type Open the dust cover and lift off the grille. For HEPA Filter Type HEPA Filter Grille Filter Micro Filter Preliminary Filter Grasp filter and pull it out with preliminary filter. [. . . ] After cleaning the secondary filter attach it in place. NOTE : The filters must be completely dried before being replaced in the dust compartment. OUTLET FILTER For Micro Filter Type Open the dust cover and lift off the grille. For HEPA Filter Type HEPA Filter Grille Filter Micro Filter Preliminary Filter Grasp filter and pull it out with preliminary filter. After cleaning preliminary filter, reposition new filter and preliminary filter by reversing this procedure. Preliminary Filter Grasp grille filter and pull it out with preliminary filter. After cleaning preliminary filter, reposition new filter compartment and preliminary filter by reversing this procedure. 9 DJ68-00093N 5/30/02 9:20 AM Page 11 USAGE OF FLOOR NOZZLE FOR RUG / FLOOR SELECTOR Before use make sure that the position of the selector is in the right position for the type of surface to be cleaned. Select the carpet indicator when cleaning carpets. [. . . ]