User manual SAMSUNG VC-D9420

[. . . ] · Because these following operating instructions cover various models, the characteristics of your WARNING vacuum cleaner may differ slightly from those described in this manual. WARNING CAUTION/WARNING SYMBOLS USED WARNING Indicates that a danger of death or serious injury exists. Indicates that a risk of personal injury or material damage exists. CAUTION OTHER SYMBOLS USED Indicates that a risk of personal injury or material damage exists. NOTE 02_ safety information IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should be observed, including the following: READ ALL INSTRUCTIONS BEFORE USING YOUR VACUUM CLEANING ROBOT. Unplug from outlet when not in use and before conducting maintenance. WARNING: to reduce the risk of fire, electric shock, or injury: GENERAL · Use only as described in this manual. · Do not operate the vacuum cleaning robot or charger if it has been damaged in any way. · If the cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped in water, return it to a customer care center. [. . . ] · If more than one vacuum cleaning robot is used simultaneously, they may malfunction due to interference of the infrared signals. 03 OPERATING operating _27 USING THE VACUUM CLEANING ROBOT Starting/Stopping Cleaning You can run or stop all vacuum cleaning robot functions. Each vacuum cleaning robot function only runs when the Power Switch is turned on. When the vacuum cleaning robot is operating, press the ( button to cancel the operation and select a function. ) Turning the power on or off Turning the power on Main unit: Press the ( ) button. Turning the power off - Remote control: Press the [Power] button. Main unit: Press and hold the ( ) button down for 3 seconds. If no key is pressed for approximately 1 minute after turning the power on, the power is automatically cut to prevent the battery discharging. To turn the power on again, press and hold the power (Start/Stop) button on the main body. Using the remote control Starting or stopping cleaning Starting - Remote control : Press the Auto, Spot, Max, Manual button. Main unit : Select Auto, Spot, Max mode by using the ( and then pressing the ( ) button. ) button When cleaning begins, the vacuum cleaning robot starts to move. ) button without selecting cleaning mode starts Pressing the ( to perform the Auto mode cleaning. Stopping To stop, press the ( ) remote control or main unit button. When the Dust Sensor icon is turned on, you can start cleaning in Dust Sensor mode. Turbo Mode CAUTION Dust Sensor Mode Cleaning Complete 30_ operating Spot Cleaning You can conveniently clean a specific area that has a a lot of cookie crumbs, dust, and etc. Move the vacuum cleaning robot to the location where you want to perform a spot clean. About 1. 5m 03 OPERATING Main unit button Remote control button Configuration Sequence 1. Cancel the mode. About 1. 5m Normal Mode - In Spot cleaning mode, the vacuum cleaning robot cleans an area with a length of 1. 5m and a width of 1. 5m. When cleaning is completed, the vacuum cleaning robot will display End, Stop, and Stand by. When the vacuum cleaning robot is docked with the charger station, spot cleaning is not supported. · Each time you press the Turbo button, the Turbo icon on the display panel is turned on or off sequentially. When the Turbo icon is turned on, you can start cleaning in Turbo mode. · Each time you press the Dust Sensor button, the Dust Sensor icon on the display panel is turned on or off sequentially. When the Dust Sensor icon is turned on, you can start cleaning in Dust Sensor mode. Turbo Mode NOTE CAUTION Dust Sensor Mode Cleaning Complete operating _31 Max Cleaning The vacuum cleaning robot automatically moves and cleans until the battery runs out and the battery level flashes only one level. If cleaning begins when the vacuum cleaning robot is docked with the charger station, the time to return to the charger is decreased since the vacuum cleaning robot remembers its original position while moving. If the vacuum cleaning robot starts the current cleaning run at a location other than the charging station and fails to locate the charging station while cleaning, it will stop near the location where it started cleaning. [. . . ] · A foreign substance (string, paper, toy etc. ) is caught in the left driving wheel. · A foreign substance (string, paper, toy etc. ) is caught in the right driving wheel. · Check the Bumper sensor. SOLUTION · Turn off the Power Switch at the bottom and move the vacuum cleaning robot to a different location. · Turn off the Power Switch at the bottom and remove the foreign substance from the power brush. [. . . ]