User manual SAMSUNG WA71NN

[. . . ] How to start the Child-Lock function: · Press the "Power" button to go to an initial washing mode. · By pressing "Start/Hold" button, you start washing and in case Child Lock function is needed during the laundry · Press and hold down the COURSE button for more than 3 seconds to run the CHILD LOCK feature. To release the function of Child-Lock: · In case the "Child-Lock" is programmed, press the "Course" button for 3 seconds. AUTO RESTART · The power is turned on automatically after power failure. 1 SAFETY INSTRUCTIONS Please note that the following precautions for safety intend to prevent unpredictable danger and damage by helping the proper use in safety. When using hot water in washing, please make sure that the water should not exceed 50°C. · Plastic parts may be deformed or damaged, and an electric shock or a fire may take place. WARNING There might be serious injury or fatal accident when you violate this instruction. [. . . ] Also an electric shock or fire may take place Don't use several appliances together with an outlet. · A fire may take place due to unusual heat. Don't press the button with an awl or pin. · An electric shock or a fire may take place. 2 FILTER LID Be sure to keep the lid closed during washing and spinning. WATER SUPPLY HOSE (COLD) DRAIN-HOSE (PUMP) Lint will be collected in the filter during washing. FABRIC SOFTENER DISPENSER SPIN BASKET POWER CORD DESCRIPTION OF PARTS The User's Manual is for common use. Make use of the User's Manual depending upon your washing machine model. 3 BLEACH INLET PULSATOR GROUND LEAD When the water pipe is metal, make sure to cover the end of the ground wire. FRONT CONTROL PANEL WATER DRAIN HOSE ADJUSTABLE LEGS Adjust the length of the legs when installing the washer. SOUND ABSORPTION PANEL For more details, see control panel of your washing machine. POWER BUTTON Press this button once to operate. Press once again to turn the power off. POWER CONTROL PANEL COURSE SELECT BUTTON COURSE With every press of this button, the washing course changes; Digital(Fuzzy) SPEEDY RINSE SPIN RINSE+SPIN Digital(Fuzzy) WATER WATER LEVEL SELECT BUTTON LEVEL According to the washload, select the water level ; MEDIUM HIGH EXTRA LOW LOW MEDIUM START/ START/HOLD BUTTON HOLD Use to pause and restart the operation. To change the washing procedure during operation, press this button to stop, and once again to restart after changing the procedure. WASHING PROCEDURE Before starting washing, check the following; Connect the water supply hose to the water tap. (In case no drain pump) Detergent Usage 1. Put the detergent evenly into the tube before placing the laundry in. If you put the detergent into the tube next to the laundry and leave it for an extended time, the laundry may become discolored. Some of the detergent may not dissolve immediately and may remain on the laundry causing damage to it, if too much detergent is used or the water temperature is too low. RINSE+SPIN 1. Press the POWER Button to "ON". Press the course select button four times. Rinsing and spin drying follow. POWER COURSE RINSE COURSE When you want rinse only do the followings. POWER COURSE START/ HOLD 4 POWER COURSE SPEEDY COURSE HOLD Because washing is speedy, it is good for light or less stained laundry. Press the POWER Button to"ON". Press the START/HOLD button Washing, rinsing, and spinning follow. If you want to pause, press the START/HOLD button again. You can change the course when paused. Close the lid. START/ POWER SPIN COURSE When you want spin only do the followings. Press the POWER Button to "ON". Close the lid. COURSE START/ Digital(Fuzzy) COURSE POWER HOLD Selects the best washing course automatically. Press the POWER Button to"ON". If you want to pause, press the START/HOLD button again. You can change the course when paused. [. . . ] · Do not use detergent, bleach or starch into the Softener Inlet. · Using too much softener may produce unsatisfactory results. · Do not open the lid during the Spin Dry cycle. If added too early, its effectiveness will decrease. · Do not leave the softener into the Softener Dispenser for a long time. Because softner became stiff. WATER SUPPLY CONNECTOR FILTER inlet water valve 1. Pull out the filter and wash well. Pull in the filter and connect the hose to the inlet water valve tightly. [. . . ]