User manual SAMSUNG WA75N6 INTRODUCTION

[. . . ] If the control panel for this washer is damaged, it must be replaced by a repair shop appointed by the manufacturer, as special purpose tools are required. q Do not operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug. q Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. q The instructions for use shall specify the maximum mass or dry cloth in kg, for which the appliance is designed. q If the appliance is supplied from a cord extension set or electrical portable outlet device the cord extension set or electrical portable outlet device should be positioned so it is not subject to splashing or ingress of moisture. q If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similary qualified person in order to avoid a hazard. 2 DESCRIPTION OF PARTS LID Be sure to keep the lid closed during washing and spinning. WATER SUPPLY HOSE DRAIN-HOSE (PUMP) SPIN BASKET Stainless FABRIC SOFTENER DISPENSER "BOOMERANG" PULSATOR BLEACH INLET POWER CORD SOUND ABSORPTION PANEL MAGIC FILTER Lint will be collected in the filter during washing. GROUND LEAD When the water pipe is metal, make sure to cover the end of the ground wire. WATER DRAIN HOSE (NO PUMP) ADJUSTABLE LEGS Adjust the length of the legs when installing the washer. 3 CONTROL PANEL x POWER BUTTON Press this button once to operate. [. . . ] Press the START/HOLD button Water level is selected automatically. Washing, rinsing, and spinning follow. If you want to pause, press the START/HOLD button again. You can change the course when paused. START/HOLD 4. Close the lid. 5 MANUAL FUNCTIONS FUNCTION WASH ONLY Press the POWER button. Press the FUNCTION SELECT button three times. Press the START/HOLD button once. Function Button BUTTON Three times RINSE ONLY Press the FUNCTION button four times. Press the START/HOLD button once. Function Button Four times SPIN ONLY Press the FUNCTION button five times. Press the START/HOLD button once. Function Button Five times RINSE AND SPIN Press the FUNCTION button six times. Rinsing and spin drying follow. Function Button Six times 6 INSTALLATION & MAINTENANCE ENVIRONMENT Leave some space Maintain at least 10cm between the washer and the wall. ASSEMBLING THE SOUND ABSORBING PANEL Tilt the washer a little and lift up the panel until it clicks, filnaly fix the panel with screw to the base as shown in the figure. Rear-side Place the washer on a sturdy flat surface. If the washer is placed on an uneven or weak surface, noise or vibration occurs. (Allowable is 1°) Adjust the legs for even placement. Never install the washer near water. Do not place the washer in steamy rooms or where the washer is directly exposed to rain. Moisture may destroy the electrical insulation causing an electrical shock hazard. CONNECTING THE DRAIN HOSE After pressing the joint ring(a), insert the drain hose(b) to drain direction. (a) Avoid direct sunlight or heaters. As plastic and electrical components are affected by direct heat, never place the washer near furnaces, boilers, etc. Do not place under direct sunlight. IN CASE OF PUMPDRAINED WASHER q Take out the q cap-hose and connect the outlet-hose. Be sure to join tightly q the drain hose into the drain-outlet on theback of the machine. Install the drain hose in the position of about 70~80cm above the ground. (b) LEVELLING SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING THE POSITION OF THE WASHING TUB. q Open the lid of the machine, pour water into the tub up to the level just below the pulsator, and adjust the legs so that the pulsator is positioned at the center of the water as shown in the figure. q Place the machine more than 10cm away from the wall. cap-hose outlet-hose 70~80cm q Adjust the legs on feet for levelling . Loosen Lock CONNECTING THE WATER SUPPLY HOSE 1. Remove the adaptor from the water supply hose. 4. Connect the water supply hose to the adaptor. Pull down the part (c) of the water supply hose . When the part (c)is released, the hose is automatically connected to the adaptor making a 'click' sound. Connect the other end of the water supply hose to the inlet water valve at the back of the washer. Screw the hose clockwise all the way in. If the water tap is a screw type, assemble a water supply hose that fits to the tap as shown. 2. First, using a "+" type screw driver, loosen the four screws on the adaptor. Next, take the adaptor and turn part(b) following the arrow for gap about 5mm between them. [. . . ] Rotate the filter counterclockwise and pull out the filter. Remove dirts and rotate the filter clockwise until it locks in position. TROUBLESHOOTING Washing machine won't work Is the water tap opened?Is there enough water? Water dose not drain Is the drain hose down?(No pump) Is the drain hose frozen?Is the drain hose clogged? If the water dose not drain in 6 minutes, a buzzer will sound. Water is not supplied Is the water tap opened? [. . . ]