User manual SAMSUNG WA80V9XIP

[. . . ] Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. The instructions for use shall specify the maximum mass or dry cloth in kg, for which the appliance is designed. If the appliance is supplied from a cord extension set or electrical portable outlet device the cord extension set or electrical portable outlet device should be positioned so it is not subject to splashing or ingress of moisture. 2 DESCRIPTION OF PARTS LID Be sure to keep the lid closed during washing and spinning. WATER SUPPLY HOSE(HOT) WATER SUPPLY HOSE (COLD) DRAIN-HOSE (PUMP) FABRIC SOFTENER DISPENSER SPIN BASKET Stainless BLEACH INLET "CENTER-JET" PULSATOR POWER CORD MAGIC FILTER Lint will be collected in the filter during washing. SOUND ABSORPTION PANEL FRONT CONTROL PANEL GROUND LEAD When the water pipe is metal, make sure to cover the end of the ground wire. ADJUSTABLE LEGS Adjust the length of the legs when installing the washer. WATER DRAIN HOSE 3 CONTROL PANEL 1. 2. POWER BUTTON Press this button once to operate. [. . . ] Press the POWER Button to"ON". POWER HEAVY COURSE 1. Press the power button to "ON". POWER 2. Press the START/HOLD button. Water level is selected automatically. Washing, rinsing, and spinning follow. If you want to pause, press the START/HOLD button again. You can change the course when paused. 3. Press the START/HOLD button Water level is selected automatically. Washing, rinsing, and spinning follow. If you want to pause, press the START/HOLD button again. You can change the course when paused. START/HOLD START/HOLD 3. Close the lid. washing is it is SPEEDY COURSE Becauselight or less speedy, laundry. good for stained WOOL COURSE Extra low water level is not available. Cold water is selected. 1. Press the power button to "ON". POWER 1. Press the power button to "ON". POWER 2. Press the course select three times. 3. Press the START/HOLD button. Washing, rinsing, and spinning follow. 3. Press the START/HOLD button Water level is selected automatically. Washing, rinsing, and spinning follow. If you want to pause, press the START/HOLD button again. You can change the course when paused. If you want to pause, press the START/HOLD button again. You can change the course when paused. START/HOLD 4. When the FUNCTION button is pressed during working, the rinse times can be changed to between 1 and 5 times in duration. Function Button five times RINSE AND SPIN Press the FUNCTION button six times. Rinsing and spin drying follow. When the FUNCTION button is pressed during working, the rinse times can be changed to between 1 and 5 times in duration. Function Button six times 6 INSTALLATION & MAINTENANCE ENVIRONMENT Leave some space Maintain at least 10cm between the washer and the wall. ASSEMBLING THE SOUND ABSORBING PANEL Tilt the washer a little and lift up the panel until it clicks, filnaly fix the panel with screw to the base as shown in the figure. Rear-side Place the washer on a sturdy flat surface. If the washer is placed on an uneven or weak surface, noise or vibration occurs. (Allowable is 1 ) Adjust the legs for even placement. Never install the washer near water. Do not place the washer in steamy rooms or where the washer is directly exposed to rain. Moisture may destroy the electrical insulation causing an electrical shock hazard. CONNECTING THE DRAIN HOSE After pressing the joint ring(a), insert the drain hose(b) to drain direction. (a) Avoid direct sunlight or heaters. As plastic and electrical components are affected by direct heat, never place the washer near furnaces, boilers, etc. Do not place under direct sunlight. IN CASE OF PUMP-DRAINED WASHER qTake out the q Be sure to join tightly q Install the drain (b) LEVELLING SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING THE POSITION OF THE WASHING TUB. q Open the lid of the machine, pour water into the tub up to the level just below the pulsator, and adjust the legs so that the pulsator is positioned at the center of the water as shown in the figure. q Place the machine more than 10cm away from the wall. cap-hose and connect the outlet-hose. the drain hose into the hose in the position drain-outlet on theback of about 70~80cm of the machine. above the ground. cap-hose outlet-hose 70~80cm q Adjust the legs on feet for levelling . Loosen Lock CONNECTING THE WATER SUPPLY HOSE 1. Remove the adaptor from the water supply hose. 4. Connect the water supply hose to the adaptor. Pull down the part (c) of the water supply hose . When the part (c)is released, the hose is automatically connected to the adaptor making a 'click' sound. 5. Connect the other end of the water supply hose to the inlet water valve at the back of the washer. [. . . ] In case the faucet is square or too big, remove the spacing ring before inserting the faucet into the adaptor. CLEANING THE FILTER NET 1. Push the upper part of the filter and pull in. 2. Open the cover as shown in the figure. Close the cover and insert the lower part of the filter in the basket first and then push the filter with "click" sound . HOW TO ADD THE FABRIC SOFTENER q When a proper amount (one time does) of fabric IN CASE OF COLD-HOT WATER WASHER q If you use only cold water inlet hose, softener is stored in the softener inlet, it is automatically put in at the last rinsing cycle. q Do not use detergent, bleach or starch into the Softener Inlet. [. . . ]