User manual SANGEAN DT-120

[. . . ] User Manual DT-120 / 180V / 180 BC D E F A H G 1 Controls 1 2 3 4 5 6 7 8 9 10 11 LCD display Band selection DBB (Deep Bass Booster) On/Off Tuning Control Stereo/Mono switch Power On/Off Volume Control Lock Switch Battery Compartment Memory button Earphone Jack Display A B C D E F G H Selected Band 90 minutes auto shut off System lock FM stereo indicator Battery power indicator Memory presets DBB on Frequency G B 2 Battery Installation Battery cover is located on the back of the unit. Slide the cover in the direction of the arrow to gain access to the battery compartment. Insert one AAA (UM-4) battery into the compartment. [. . . ] Display will show the changes when you operate the volume control. 4 Tuning the radio Band AM Frequency DT-120/DT-180 DT-120/DT-180 DT-180V DT-180V Antenna 522 - 1629 kHz (9 kHz) 520 - 1710 kHz (10 kHz) 522 - 1629 kHz (9 kHz) 520 - 1710 kHz (10 kHz) Internal/Rotate radio for bes reception Band FM Frequency 87. 50 - 108 MHz Antenna External/Make sure the earphone in plugged into earphone jack Band TV Frequency TV channels 2-13 (DT-180V) Antenna External/Make sure the earphone is plugged into earphone jack 5 90 Minutes auto shut off device For saving battery power, this radio is designed to auto shut off after 90 minutes operation, LCD display shows . For continuous listening if necessary, pressing Power On/Off button for more than 2 seconds until LCD display disappears. Scan Tuning Turn on the radio, select required band by pressing Band Selection button. Press and hold down the Tuning Control buttons for more than half a second and release the button to commence Scan Tuning. The radio will scan and stop automatically when a station is found. G B 6 Manual tuning Turn on the radio, select required band by pressing Band Selection button. Desired station may be selected by pressing the Tuning Control buttons intermittently until the desired station is reached. Or pressing and holding the Tuning Control until the desired station is reached. Memory Tuning (Station Preset) Turn on the radio by pressing Power On/Off button. Select required band by pressing Band Selection button. Tune to the desired station using the Scan or Manual tuning described above. When the desired station is reached, press and hold Memory button for more than 2 seconds until display M x stop flashing followed with a beep (via earphone). It will replace previous memory station. You may store 5 memory stations each band (AM, FMI, FMII and TV). 7 Recall memory stations Turn on the radio, select required band then simply press and release Memory station button. LCD display will show Memory preset and radio frequency. Stereo/Mono switch The radio is designed to receive FM stereo broadcastings. For weak FM station, switch Stereo/Mono to Mono position. LCD display Stereo icon will disappear. G B 8 Change AM band tuning step For Northern American countries and some South American countries, AM tuning step is 10 kHz. [. . . ] It's important to make sure Lock switch is in its off position when radio is to be operated, as radio is completely inoperative until Lock Switch is released. G B 10 Specifications Battery: 1 x AAA (LR03, UM-4) Frequency Coverage: FM: 87. 50 ­ 108 MHz AM: 522 ­ 1629 kHz ( DT-120/DT-180 9 kHz) 520 ­ 1710 kHz ( DT-120/DT-180 10 kHz) 522 ­ 1629 kHz (DT-180V 9 kHz) 520 ­ 1710 kHz (DT-180V 10 kHz) TV: 2 ­ 13 channel (DT-180V) Output Power: 1. 0 mW + 1. 0 mW Earphone Jack: 3. 5 mm diameter (stereo) The company reserves the right to amend the specifications without notice. 1 1 If at any time in the future you should need to dispose of this product please note that: Waste electrical products should not be disposed of with household waste. Check with your Local Authority or retailer for recycling advice. (Waste Electrical and Electronic Equipment Directive) G B 12 [. . . ]