User manual SANGEAN DT-200V

[. . . ] LOCATION OF CONTROLS Congratulations and welcome to The SANGEAN WORLD OF LISTENING! To insure proper operation please famililarize Yourself with these instructions before using your New receiver 1 . Belt Clip 2 3 2 1 4 11 9 10 5 6 7 8 13 3 14 12 4 BATTERY INSTALLATION The battery cover is located on the back of the unit. Slide the cover in the direction of the arrow to gain access to the battery compartment(12). [. . . ] Select AM, FM or TV Band by pressing Band Selection Button (7). Desired station May be selected by either pressing the Tuning Control(5)or(6) intermittently until the desired Station is reached or pressing and holding the Tuning Control until the desired station is Reached. Release and push the Tuning Control once again to retain the desired Station. C MEMORY TUNING(STAION PRESET) Turn on the Ridio by pressing On/Off Button (1). Select AM or FM Band by pressing Band Selection Button (7). Tune to the desired staTion using the Manual or Scan Tuning Methods As reached and indicated in the desired station Is reached and indicated in the LCD Display (4) Press the Memory Button (9). A M will flash in the LCD Display. During its flashing push the Select Button (10). The Number of the Memory position will appear successively each time the Select Button is pressed. Select the Number Position for the station appearing in the LCD Display by pressing the Menory Button (9) when the correct position appears 8 In the LCD Display. You may store a total of 19 stations in any mix from any band. Original stations are eliminated when new stations are selected to take their places. D MEMORY TUNING (STATION RECALL) Turn on the Radio by pressing On/Off Button (1). Select AM, FM or TV Band by pressing Band Selection Button (7). Pressing and Holding the Select Button (10) for more than 1/2 second will begin displaying the stored station and their associated numbers one by one in the LCD Display . Numbers order of display may be changed form ascending to descending and vice versa at any time by pressing the Tuning Controls (5) or (6) . It is only necessary to press the Select Button a second time when the desired station appears in the LCD Display to retain the desired station MONO/STEREO BUTTON Monaural or Stereo reception may be selected Through the Headphones during FM reception by Alternately pressing the Mono/Stereo Button (8). The Speaker On/Off Switch (11) must be in the Off Position. 9 LOCK SWITCH To prevent accidental changing of any o the radio settings move the Lock Switch (13)to its up , locked position( ). To release simply move the switch to its down position. IT IS IMPORTANT TO MAKE SURE LOCK SWITCH IS IN ITS DOWN POSITION WHEN RADIO IS TO BE USED AS RADIO IS COMPLETELY INOPERATIVE UNTIL LOCK SWITCH IS RELEASED . If the Radio is not to be Used for any extended period of time battery power Savings may be realized by setting-Lock Switch In its locked ( ) position during storage. BELT CLIP A removable Belt Clip(14) is provided on the back Of the unit. It can be removed by gently pushing Where indicated on the back of the clip and moving The clip in the direction of the battery case ad inDicated in the illustration. Reverse procedure to Reinstall clip. 14 14 REMOVAL REINSTALL 10 SPECIFICATIONS Type: FM-Stereo(Via headphones) AM Standard(mono) TV Band (mono, CH. 2-13VHF) Earphone Jack:3. 5mm mini-plug 32 ohm impedance (stereo) Output Power:60mW(10%THD) Via built-in speaker 32 ohm impedance(stereo) Speaker:1 inch diameter, 4 ohms impedance External Power: Speaker AM 60 FM/TV 78 Batteries:3 Volts(AA size)x 2 Dimensions (Wx Hx D): 4 3-8"Hx2 5/8"W x3/4"D Weight:5. 0 ounces approximately without batteries. Earphones 50MA 68MA 11 MAINTENANCE 1. Keep the radio dry. If it does get wet, wipe it immediately. Liquids may contain chemicals that can corrode electronic circuitry. [. . . ] 6. Use only fresh batteries of the recommended size and type. Always remove old or weak batteries as they can leak and destroy electronic components and circuitry. 7. Modifying or tampering with the radio 's internal components can cause a malfunction, and will void the product's warranty. WARRANTY Please see the Statement of Limited Warranty enclosed with your Sangean Product for complete details. [. . . ]