User manual SANGEAN WR-2

[. . . ] Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged. Liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, shall not be placed on the apparatus. Light button 2 Radio band/AUX IN selection 3 Memory presets 4 Power On/Off/Sleep button 5 Rotary Tuning Control 6 Volume/Tone control 7 IR sensor 8 Traffic information button and minute adjustment 9 Auto time button and hour adjustment 10 Alterative frequency and Select button 11 Set button 12 Display button 13 Station search and mono button 14 Earphones jack External F-type FM antenna terminal 16 External AM antenna terminal ( USA version only ) 17 AC power cord socket 18 12V DC input socket ( ideal for vehicles/boats ) 19 REC out socket 20 Aux in socket 21 External/Internal antenna switch Power on/off/Sleep button 2 Tuning control 3 Volume control 4 Tone control 5 Memory presets 6 Mute 7 Traffic button and minute adjustment 8 Auto time button and hour adjustment 9 Alternative Frequency and Select button 10 Set button 11 Display button 12 Radio band and Aux in selection Frequency/Time/Station display B Radio/Buzzer alarm symbol C Daylight Saving Time ( DST ) , not applicable for WR-2 D Sleep/Snooze status E RDS indicator F Time indicator G Stereo indicator H Traffic indicator I Aux In level attenuation J Memory presets AC operation Before you plug the AC cord into the radio, be sure the AC voltage is correct. [. . . ] Press and continue to hold down the Power On/Off/Sleep button, the display will cycle through the available sleep times in the order GB 60-45-30-15-120-90-60. Release the button when the required sleep time appears in the display and the radio will play the last station selected. To turn on display illumination, press and release Light button. By pressing and releasing Light button, you may also adjust display brightness or turn off the illumination completely. Operating your radio FM Connect the antenna The radio comes with Built-in AM/FM antenna. Be sure to switch external/internal antenna switch to External position while using the supplied wire antenna or connect the outdoor antenna. In some European countries, you may have to connect the supplied antenna terminal adaptor to connect with the outdoor antenna. Operating your radio AM Connecting the antenna The radio comes with built-in AM antenna which should be enough for normal listening. To improve the AM reception, you may connect the outdoor AM antenna with AM antenna terminal (USA version only). Your radio is equipped with three tuning methods ­ Scan tuning, Rotary manual tuning and Memory preset tuning. When switch on your radio will display the waveband and frequency in use. Press and release Scan button, your radio will scan the selected waveband and stop automatically when it finds a station of sufficient strength. Switch on your radio by pressing the power button. Press and hold down either the tuning up or down button until the frequency in the display begins to change rapidly. Your radio will scan the selected the waveband, stopping each time it finds a station of sufficient strength. There are 5 memory presets for each FM and MW wavebands. Press and hold down the required Preset button until the radio beeps (greater than 2 seconds). Stations stored in preset memories may be overwritten by following the above procedure. Rotary the volume control knob to set the required volume level, display will show volume level ( maximum to 60 ) 2. Press Volume control once to get into Treble control. Press Volume control twice to get into Bass control. If a station being received is weak , some hiss may be audible. [. . . ] If AF information has not yet been received or is not provided by the station you are listening to, the radio will remain at the current frequency and the display will indicate "NO AF ". If the station does not provide traffic information, the symbol will not appear and the radio will display NO TP/TA indicating that no traffic information is available. If the radio is tuned to a national stations such as BBC Radio 4, it will automatically re-tune to any BBC local station broadcasting traffic announcements. When the traffic announcement is finished, the radio will re-tune to the previously selected station. [. . . ]