User manual SANUS COMPONENT FURNITURE AV CABINET-CFA21CB

[. . . ] If you have any questions regarding this product, contact Sanus at 800. 359. 5520 or visit www. sanus. com. Our customer service representatives can quickly assist you with missing or damaged parts. Replacement parts for Sanus products purchased through authorized dealers can be shipped directly to you. Please call Sanus Systems before returning products to the point of purchase. [. . . ] Repeat process for the other Front Rail, making sure it is level with the top of the corner pillar. Top View A (Front Left Corner) Diagram 2 r allen bolt clamp p Step 3: Add second Side Panel Assembly Attach the second Side Panel Assembly (r) by lining up and inserting both Front Rails (p) into the groove in the corner pillar. If the clamp on the Front Rail will not fit in the groove, make sure the allen bolt (labeled in the Top View) is loose so the clamps are close together. Once you have the Front Rails alligned so the bottom one is resting on the Foot (m), and the top one is level with the corner pillar, tighten the allen bolt in the back of the Front Rail to widen the clamp to secure it to the pillar. See the Top View of Diagram 3 for assistance. Top View (Front Right Corner) Diagram 3 allen bolt r p clamp Step 4: Attach the Back Rails Attach the Cam Pins (b) to the Back Rail (q). Make sure the arrow on each Cam is facing the hole in the outside of the Back Rail and add two Cam Pins to each end of the Back Rail as shown in the Detailed View of Diagram 4. Insert the Cam Pins until there is a small space between the head of the pin and the Back Rail. Attach the Back Rail by sliding the cam pins down the groove on the Side Panel pillar as shown in the Top View of Diagram 4. Once the Back Rail is resting on the Foot (m), tighten the cams labeled in Diagram 4 to hold it in place. Make sure the bottom Back Rail is oriented so the threaded holes near the ends are on the top, and the Cams face inside the cabinet, as seen in Diagram 4. Make sure the top Back Rail is oriented so the threaded holes near the ends are on the bottom, and the Cams face inside the cabinet, as seen in Diagram 4 Diagram 4 Detailed View Top View (back left corner) b cam b r q q Step 5: Add the Back Panel Insert a Back Panel Bolt (d) through the Back Panel (s), a Spacer (e) and thread it into the Back Rail (q) as seen in the Detailed View of Diagram 5. Repeat the process until all 4 Back Panel Bolts are attached to the Back Rails. Proceed to tighten the Back Panel Bolts. Diagram 5 Detailed View q e d s Step 6: Add Shelves Thread a Bottom Shelf Pin (f) into the Side Panel (r) as shown in Detailed View B of Diagram 6. Repeat process until all four Bottom Shelf Pins have been inserted into the Side Panel. Proceed to press fit the Bottom Shelf (w) so it is locked into the Bottom Shelf Pins. To add the Glass Shelf (v), insert 4 Shelf Pins (g) at the desired height into the Side Panels as shown in the Detailed View A of Diagram 6. Proceed to place the Glass Shelf on the Shelf Pins. Detailed View A Diagram 6 r g Detailed View B r f Step 7: Prepare the top Insert a Dowel (c) into each corner hole in the Top (u). Gently tap the Dowels in. Diagram 7 c u Step 8: Fit Top to assembly Press fit the Top (u) to the assembly so the Dowels (c) go into the holes in the corner pillars as seen in the Detailed View of Diagram 8. [. . . ] The slot on the end of the Hinge will fit around the bolt on the Hinge Plate. The top and bottom Hinges should engage at the same time as shown in Diagram 11. Once the two parts of the Hinge are mated, tighten the bolt on the Hinge Plate firmly with a screwdriver. Diagram 11 Detailed View t o n k Step 12: Hinge Adjustment Each hinge Assembly is adjustable in multiple directions. [. . . ]