User manual SANUS COMPONENT FURNITURE VIDEO LOWBOY-CFV69CB

[. . . ] See complementary Sanus products at www. sanus. com Parts: Foot - T Qty. 2 Step 1: Add feet WARNING: The ends of the Carpet Spikes are very sharp and may scratch floors or furniture. All sharp objects can be hazardous to children. For this reason Sanus Systems provides the carpet spikes as an option. [. . . ] Repeat this process until all four Bottom Shelf Pins have been inserted into both Side Panels. Press fit the Bottom Shelf (Z) until it is locked into the Bottom Shelf Pins (M). Diagram 4 GG Z Z GG GG M Step 5: Add Center Dividers Insert a Barrel Nut (J) into the top and bottom of the Left and Right Center Dividers (HH, II) as in Detail A, Diagram 5. NOTE: Make sure the threaded hole in the Barrel Nut (J) lines up with the hole in the back of the Center Dividers (HH, II), and the arrow on the Cam is pointing toward the hole in the bottom as in Detail B, Diagram 5. Insert four Threaded Cam Pins (I) into the Bottom Shelf (Z) as in Detail C, Diagram 5. Attach the Center Dividers (HH, II) to the Bottom Shelf (Z); then, tighten each Cam with a phillips screw driver, turning the Cam clockwise. Diagram 5 HH II Z HH or II Cam I J Z Detail A Detail B Detail C Step 6: Add Top Rails AA NOTE: Make sure the Flange on the Front Rail (AA) faces the back of the unit. Flange Attach the Front Rail (AA) to the Side Panel Assemblies (GG) by sliding the clamp down the groove in each Side Panel Pillar as done in Step 2. When Front Rail (AA) is level with the tops of the Center Dividers (HH, II), tighten the Allen Bolt on the back side of the Front Rail to expand the clamp, thus holding the Front Rail firmly in place. NOTE: Make sure the arrow on each Cam is facing the hole in the outside of the Back Rail (BB). Insert two Cam Pins (B) into each end of the Back Rail (BB) until there is a small space between the head of the Cam Pin and the Back Rail as shown in Diagram 6. Attach the Back Rail (BB) by sliding the Cam Pin (B) down the groove on the Side Panel Pillar. Once the top of the Back Rail is level with the top of the Center Dividers (HH, II), tighten each Cam with a phillips screw driver, turning the Cam clockwise. Diagram 6 BB Cam BB GG AA B GG HH II Step 7: Add Barrel Nut Bolts NOTE: You may need to loosen Cams tightened in Step 6 to Line up the holes. If you do, make sure to tighten them when finished with this Step. Thread the Barrel Nut Bolts (K) through the Back Rail (BB) and into the Center Divider Panels (HH, II); then, tighten the Barrel Nut Bolts (K) until the Back Rail (BB) is secured to the Center Divider Panels (HH, II). Diagram 7 HH II BB BB K Step 8: Add Bottom Shelf Retainer Gently rotate the cabinet so it is resting on its back; then, using the Wood Screws (N) secure the Bottom Shelf Retainers (V) to the Bottom Shelf (Z). Diagram 8 N V Z N V Step 9: Add the Back Panels Insert a Back Panel Bolt (D) through the Outer Back Panels (CC), Center Back Panel (DD), and a Spacer (C); then, thread it into the Back Rail (BB). Repeat the process until all 12 Back Panel Bolts are attached to the Back Rails. Diagram 9 BB C D BB CC CC DD CC Step 10: Add Top Insert a Dowel (H) into each hole in the bottom of the Top (Y). Align the Dowels (H) in the bottom of the Top (Y) with the holes in the Center Dividers (HH, II) and the pillars on the Side Panels (GG); then, press fit the Top onto the Side Panels, and Center Dividers. Diagram 10 Y H H GG GG HH II Step 11: Add Isolation Pads to Isolation Shelf NOTE: Make sure the soft side of the Isolation Pad is facing toward the shelf when inserting it into the Isolation Shelf. [. . . ] Tighten each Hinge screw until the Hinge is secure to the Side Door. Diagram 17 Q W KK Step 18: Add Side Doors Attach the Hinge Plates (X) by threading a Hinge Plate Screw (R) through each hole in the Hinge Plate and into the Side Panel (GG). Repeat this process until all four Hinge Plates are attached; then, tighten the Hinge Plate Screws with a phillips screw driver. NOTE: To attach each Hinge (W) to its Hinge Plate (X), the bolt along the back center of the Hinge Plate must be loose during installation. [. . . ]