User manual SANUS F42A

[. . . ] CSAV makes no representation of warranty, expressed or implied, regarding the information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. INTRODUCTION TOOLS REQUIRED FOR INSTALLATION · No tools are required for this installation INSPECT MOUNT BEFORE ASSEMBLY Carefully inspect mount assembly for shipping damage (see Figure 1). If damage is apparent, call your carrier claims agent and do not continue with installation until the carrier has reviewed the damage. NOTE: Thoroughly read and understand all assembly instructions before starting installation. Table 1: PARTS IMPORTANT WARNINGS AND CAUTIONS! WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. ITEM 10 20 30 DESCRIPTION FRAME, Decorative Display INSTRUCTIONS, Installation LENS, Optical (when ordered sepreately) QTY. [. . . ] NOTE: Depending on the brand and model of display, this measurement may or may not be the same as the width of the upper bezel. Step 1 Step 2 Step 3 Figure 1 Display Size Compatability Tables TELEVISIONS MAXIMUM ALLOWABLE DIMENSIONS Diagonal Dim. 32 42 50 Height (inches / mm) 23 31/32 (609mm) 28 57/64 (734mm) 32 27/32 (834mm) Width (inches / mm) 37 3/32 (942mm) 45 13/16 (1164mm) 52 25/32 (1341mm) 3 32", 42", and 50" Installation Instructions Lower Spacer Mounting Bracket Alignment Bar INSTALLATION WARNING: IMPROPER INSTALLATION CAN LEAD TO ACCESSORY OR DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT!It is the installer's responsibility to make sure the combined weight of all components attached to display does not exceed the weight capacity of the display mount! IMPORTANT !: If optional optical filter is being used it must be installed before proceeding to frame installation. (See page 5) 1. Lay frame face down on a clean, dry, smooth surface. Slide spacer locking tab towards back of frame. Slide spacer assembly to left until free of UPPER spacer mounting bracket and remove from frame. (See Figure 2) Spacer Locking Tab Upper Spacer Mounting Bracket Figure 3 5. Position spacer assembly on top of display with wing nuts facing towards rear of display and alignment bar resting on display top. Slide LOWER spacer mounting bracket up or down until rubber edge on bottom of bracket is aligned with lower edge of display bezel. (See Figure 4) Alignment Bar Figure 2 4. Loosen three wing nuts on spacer assembly until alignment bar can slide freely in slots of LOWER spacer mounting bracket. : DO NOT completely remove wing nuts. Lower Spacer Mounting Bracket Lower Edge of Display Bezel Figure 4 4 Installation Instructions 7. Tighten three wing nuts on spacer assembly. Slide top of LOWER spacer mounting bracket into UPPER spacer mounting bracket until it stops. (See Figure 5) NOTE: Wing nuts should be facing towards rear of frame when spacer assembly is properly installed. Slide spacer locking tab towards front of frame. (See Figure 5) Spacer Locking Tab Upper Spacer Mounting Bracket 32", 42", and 50" IR Receiver (example Location) IR Replicator Adhesive back Figure 6 17. Slide frame onto display until display front presses against inside of frame. : Make sure spacer alignment bar is resting on top of display. Wire with Plug From IR Replicator Straps Figure 5 10. [. . . ] Turn hold down tabs until positioned over lens. (See Figure 10) Figure 10 6 Installation Instructions 32", 42", and 50" 7 32", 42", and 50" Installation Instructions USA/International Europe Asia Pacific A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800. 359. 5520 / 651. 484. 7988 651. 636. 0367 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Room 30I, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112 P +86-755-8996 9226 ; 8996 9236 ; 8996 9220 F +86-755-8996 9217 USA/International Europe Asia Pacific 8809-000036 RevB 2007 CSAV, Inc. 11/06 A P F A P F A 2221 Highway 36 West, St. [. . . ]