User manual SANUS VISIONMOUNT CENTER CHANNEL SPEAKER MOUNT-VMCC1

[. . . ] Required Tools: Phillips screw driver and crescent wrench. Supplied Parts and Hardware: Hardware shown as actual size. (1) Left Upper Extension - a (1) Right Upper Extension- b (2) Lower Extension - c (2) Axis Bracket - d (2) Bar Bracket - e (2) Speaker Bracket - f (1) Support bar - g (2) M4 x 10 Bolt - h (2) M5 x 10 Bolt - i (10) 1/4 - 20 x 3/8 Bolt - j (10) 1/4 - 20 x 5/8 Bolt - k (2) Spacer - l (8) 1/4 - 20 Nut - m (2) 1/4 - 20 x 1500 Bolt - n Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 11. 16. 05 (6901-100133) Customer Service: 800. 359. 5520. See complementary Sanus products at www. sanus. com For assembly information for the VMSA, VMAA, VMAA18 and VMAA26 see the Steps 1 through 6. For assembly information for the VMDD and VMDD26 see Steps 7 through 12. [. . . ] In this case, Speaker Bracket (f) may be attached directly to the Upper Extensions (a, b) Configuration 1 Configuration 2 a b j j c j j c f f Step 6: Add Speaker Attachments to assembly Thread a 1/4 - 20 x 3/8 Bolt (j) up through each Upper Extension (a, b) and into the Bar Bracket (e). Thread a 1/4 - 20 x 5/8 Bolt (k) up through each of the Upper Extensions. Do not tighten the 1/4 - 20 x 5/8 Bolts at this time, you will tighten these so they bottom out into the Support Bar after the speaker is attached. Note: For Speakers that have threaded inserts that are spaced between 1. 75 inches and 15. 5 inches use configuration 1. If the threaded inserts on the speaker are spaced wider than 15. 5 inches, the tabs on the Speaker Brackets should face away from each other. In Diagram 6, Speaker Brackets shown facing toward each other. Detailed View Diagram 6 e a, b j k Assembly Instructions for the VMDD and VMDD26 flat panel wall mounts. Step 7: Remove mount from Wall Plate and remove lower Cross Tube from the mount assembly. Loosen the Allen Bolts in the lower four Vise Assemblies and remove the lower Cross Tube from the mount assembly. Diagram 7 vise assemblies cross tube Step 8: Add Axis Brackets If the threaded inserts on your speaker are spaced between 1. 5 inches and 5. 7 inches, you do NOT need to use the Support Bar (g) for the installation. Position the Axis Bracket (d) so it fits the Axis Assembly on the mount. Insert 1/4 - 20 x 5/8 Bolt (k) through the outer side of the Axis Bracket, Axis Assembly, and into a 1/4 - 20 Nut (m). Insert a 1/4 - 20 x 1. 5 Bolt (n) through the inner side of the Axis Bracket, a Spacer (l), the inner edge of the adjacent Axis Bracket. Slide the Support Bar through the slots in each Axis Bracket until centered with the wall mount. Detailed View Diagram 8 k m l m axis assembly axis assembly n d d Step 9: Add Bar Brackets Note: If the Support Bar was not installed in Step 8, only re-install the cross tube in this step. Slide the lower Cross Tube through the first Monitor Bracket, first Bar Bracket (e), both Axis Assemblies, a second Bar Bracket and through the second Monitor Bracket. Tighten all four Vise Assemblies to secure the Cross Tube once it is slid through the second Monitor Bracket. Thread each 1/4 - 20 x 5/8 Bolt (k) through each hole in the bottom of the Axis Bracket (d) until they bottom out against the Support Bar (g). Diagram 9 Detailed View g d k Step 10: Configure Speaker Attachments - Support Bar Not installed. If using Support Bar, see Step 5 for configuration. Configure the Speaker Attachments as seen below. Tighten all Bolts with a Phillips screw driver. Repeat process for the second Speaker Attachment. [. . . ] Select the proper bolt for your center channel speaker by hand threading the M4 x 10 Bolt (h), M5 x 10 Bolt (i) or 1/4 - 20 x 3/8 Bolt (j) into the into the threaded inserts in the back of the speaker to determine which fits. Once you have selected the proper bolt, insert it through each of the Speaker Brackets and thread it into the center channel. Tighten each Bolt with a Phillips screw driver. You can now center the speaker with the TV by sliding it left or right. [. . . ]