User manual SANUS VISIONMOUNT FLAT PANEL CEILING MOUNT-VMCM1

[. . . ] Sanus Systems can not be liable for damage or injury caused by incorrect mounting, incorrect assembly, or incorrect use. Please call Sanus Systems before returning products to the point of purchase. Required Tools: Phillips screw driver, wrench or socket set Supplied Parts and Hardware: Some parts not shown at same size* (1) Coupler - a* (1) NPT Tube - b * (1) Axis Assembly - c (2) 1" Diameter Tube - d (4) Vise Assembly - e* (2) Monitor Bracket - f Sanus Systems 2221 Hwy 36 West, St. Paul, MN 55113 10. 18. 05 Customer Service: 800. 359. 5520. [. . . ] The Vise Assembly should be able to rotate freely around the Carriage Bolt. Place the Vise Assembly (e) between the two sides of the Monitor Bracket (f) so that the two jaws point toward the set of 1" diameter holes and the allen bolt is facing away from the television as shown in the Detailed View of Diagram 3. Place a Carriage Bolt (g) through the square hole in the side of the Monitor Bracket, through the hole in the Vise Assembly, and then through the square hole in the other side of the Monitor Bracket also shown in Diagram 3. Next, tighten a 1/4-20 Nut (h) onto the end of the Carriage bolt. Repeat this step for the bottom of the Monitor Bracket. Finally, repeat these two steps for the second Monitor Bracket. Detailed View Diagram 3 allenbolt f e g h Step 4: Attach the Axis Assembly to the Television Warning: The 1" Diameter Tubes must extend beyond the outside edges of both Monitor Brackets and the Allen Bolts in all 6 Vise Assemblies must be tightened for the installation to be safe!First, orient each Vise Assembly (e) so that a 1" Diameter Tube (d) will pass through the 1" round hole in the Monitor Bracket (f) and then between the jaws of the Vise Assembly. Insert a 1" Diameter Tube through the top hole in the first Monitor Bracket as shown in Diagram 4. Repeat this step for the Bottom hole in the same Monitor Bracket. Diagram 4 d f e Step 5: Attach the Axis Assembly (cont) Position the Axis Assembly (c) so that the allen bolts are facing away from the TV and the quick connect is on the top as shown in Diagram 5. Line up the two 1" diameter holes at the top and bottom of the Axis Assembly with the with the 1" Diameter Tubes (d). Continue to push the 1" Diameter Tubes through the Vise Assembly on the Axis Assembly and then through the other Monitor Bracket (f). Again, make sure the Vise Assemblies on both the Axis Assembly and the second Monitor Bracket are oriented so that the 1" Diameter Tubes will pass between the jaws. Once the 1" Diameter Tubes are in place, tighten the allen bolts on the 4 Vise Assemblies in the two Monitor Brackets with the Allen Key (m) to lock the television to the mount. Next, slide the Axis Assembly into the desired position between the two Monitor Brackets and tighten the two remaining Vise Assemblies inside the Axis Assembly. Note: Sanus recommends Axis Assembly to be centered between the Monitor Brackets. Diagram 5 f e d c viseassembly Step 6: Attach Coupler Thread the Coupler (a) onto the NPT Tube (b) until tight. Diagram 6 Detailed View a b Step 7: Attach the NPT Tube To attach the NPT Tube (b), simply thread the Coupler (a) onto an existing NPT Tube. Make sure the lower NPT Tube is oriented so the quick connect is facing toward the front as shown in the Side View of Diagram 7. [. . . ] The Nut in the Detailed View can be slightly tightened or loosened to adjust the tension of the Swivel. Once you have tilted the TV forward and removed the Safety Bracket, you can use the Safety Bracket to adjust the tension. Make sure a flat side of the tension nut is parallel with the TV before putting the Safety Bracket back on. Detailed View Adjust Swivel Tension Diagram 9 tension nut tension allen knobs bolts Step 10: Cable Management Leave some slack in the cables so that during motion there is no added tension on the connectors. [. . . ]