User manual SANUS VISIONMOUNT LCD WALL MOUNT-VMFL1

[. . . ] Assembly Instructions for Model: VMFL1 Thank you for choosing a Sanus Systems Vision Mount wall mount. The VMFL1 is designed to mount up to 30" [76. 2 cm] LCD flat panel televisions weighing up to 40 lbs [18 Kg] to a vertical wall. It will allow the television to be just 0. 5" [12. 7 mm] from the wall. [. . . ] 2 Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 02. 23. 06 (000026) Customer Service: 800. 359. 5520. See complementary Sanus products at www. sanus. com Step 1: Hang Wall Plate NOTE: Make sure the Wall Plate (A) is oriented so the flat surface in the center of the plate is against the wall as shown in Diagram 1A. Wood Stud Mounting: Using a high quality stud sensor to locate a stud: then, using the Wall Plate (A) as a template mark two holes in the appropriate location, making sure the hole is in the center area of the stud. Pre-drill a 1/8" hole 2. 5" [63. 5 mm] deep where the upper Lag Screw (C) will be installed; then, secure the Wall Plate (A) to the stud using one of the Lag Bolts as shown in Diagram 1A. Verify that the Wall Plate is level; then pre-drill a 1/8" hole 2. 5" [63. 5 mm] deep for the lower Lag Screw (C) and secure the bottom of the Wall Plate (A) with the second Lag Screw as shown in diagram 1A. Drywall Installation: Position the Wall Plate (A) in the desired location on the wall; then, use the Wall Plate as a template and mark the location of the four outer mounting holes. Using a 3/8" drill bit, proceed to drill a 3/8" pilot hole in each marked location. Install a Dry Wall Anchor (D) in one of the pilot holes and tighten the Anchor Bolt until it is fully seated as shown in Diagram 1B. NOTE: Make sure the Washer is between the head of the Anchor Bolt and the Wall Plate (A) as shown in Diagram 1C. Loosen the Anchor Bolt approximately 1/4" and repeat the above process for the three additional pilot holes. Once Wall Plate (A) is mounted onto the wall, verify that it is level; then, proceed to tighten all four Anchor Bolts. Diagram 1A Level A Insert Dry Wall Anchor (D) Tighten Bolt Until Anchor is against wall Step 2: Install M5 Locking Bolts Insert both M5 Locking Bolts (H) through a M5 Spacer (L); then, thread the M5 Locking Bolts into the Monitor Bracket (B) just enough to engage the threads as shown in Diagram 2. Diagram 2 Diagram 1B Drill 3/8" Pilot Hole A Washer must be between Anchor Bolt and Wall Plate (A) Diagram 1C Level C B L H Step 3: Attach Monitor Bracket to flat back TV To attach the Monitor Bracket (B) to the TV, insert a M4 x 10 mm Bolt (E) through the countersunk hole in the Monitor Bracket, and the M4 Washer (I); then, thread it into the TV. Repeat this until all four bolts are secured to the TV, as shown in Diagram 3. Tighten each M4 x 10 mm Bolt with a phillips screw driver. Diagram 3 I B E Step 4: Attach Monitor Bracket to a TV with a recessed hole pattern To attach the Monitor Bracket (B) to the TV, insert a M4 x 20 mm Bolt (F) through the countersunk hole in the Monitor Bracket, and the Small M4 Spacer (J); then, thread it into the TV. [. . . ] Once all cables are installed, lift the TV just enough to engage the two lower hooks on the Monitor Bracket (B) with the slots in the Wall Plate (A) as shown in detail 7B Tighten both M5 Locking Bolts (H) to secure the Monitor Bracket (B) to the Wall Plate (A). Diagram 7A Diagram 7B A A B H B Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 02. 23. 06 (000026) Customer Service: 800. 359. 5520. See complementary Sanus products at www. sanus. com [. . . ]