User manual SANUS VISIONMOUNT VESA 400 MM X 200 MM ADAPTER-MA1A

[. . . ] Wood Stud mounting: The Wall Plate (a) must be mounted to two wood studs at least 12" apart. Use a high quality stud sensor to locate two adjacent studs. It is a good idea to verify where the studs are located with an awl or thin nail shown in Diagram 1a. 5" deep hole at the desired height in each stud using a 3/16" drill bit. [. . . ] Make sure these holes are in the center area of the studs and level with each other. Use the Wall Plate as a template to mark the location of the second hole in each stud. 5" deep holes using the 3/16" drill bit in the marked location. Make sure the Wall Plate is oriented so the flat surface in the center of the plate is against the wall and that a set of Lag Bolts is on each side of the two large holes in the center as shown in Diagram 1b. brick , Solid Concrete and Concrete Block mounting: Use the Wall Plate (a) as a template to mark 6 hole locations on the wall. The outer holes must fall to left and right of the two large holes in the middle of the plate. Three in the top row of slots and three more in the bottom row. Make sure these holes are level and there is at least 6" between any two holes. Pre-Drill these holes with a 1/2" masonry bit to at least 2. Insert a Concrete Anchor (v) into each of these holes. Make sure the anchor is seated completely flush with the concrete surface even if there is a layer of drywall or other material in front. see Detailed View B of Diagram 3 for assistance. Proceed to tighten the Bolts firmly with a phillips screw driver. Step 4: Attaching the Monitor Brackets to a television with a curved back WARNING: DO NOT LAY THE TELEVISION FACE DOWN ON THE GLASS, lean it up against a wall or other solid surface!Laying the television down on the glass may cause permanent damage. The Monitor Brackets (c) should be placed as vertically close to center of the television as possible before installation. If your TV has a curved back and requires either a M4 or M5 diameter bolt, thread a M4 x 30 (f) or a M5 x 30 (h) Bolt through the appropriate Lock Washer (m, n), an M4/M5 Washer (t), the Monitor Bracket, an M4/M5 Washer, a M4/M5 Spacer (q) and into the TV as seen in Detailed View A of Diagram 4. If you determined that your TV requires a Bolt with a M6 or M8 Diameter, thread a M6 x 35 (j) or a M8 x 40 (l) Bolt through the appropriate Lock Washer (o, p), the Monitor Bracket, a M6/M8 Spacer (r) and into the TV as seen in Detailed View B of Diagram 4. Proceed to tighten the Bolts firmly with a phillips screw driver. Step 5: Attaching the Monitor Brackets to a television with recessed threaded inserts. WARNING: DO NOT LAY THE TELEVISION FACE DOWN ON THE GLASS, lean it up against a wall or other solid surface!Laying the television down on the glass may cause permanent damage. [. . . ] WARNING: DO NOT LAY THE TELEVISION FACE DOWN ON THE GLASS, lean it up against a wall or other solid surface!Laying the television down on the glass may cause permanent damage. The Monitor Brackets (c) should be placed as vertically close to center of the television as possible before installation. If your TV has threaded inserts that are recessed and requires either a M4 or M5 diameter bolt, thread a M4 x 30 (f) or a M5 x 30 (h) Bolt through the appropriate Lock Washer (m, n), an M4/M5 Washer (t), the Monitor Bracket, an M4/M5 Washer, a M4/M5 Spacer (q) and into the TV as seen in Detailed View A of Diagram 5. [. . . ]