User manual SANUS VXF220

[. . . ] English Wood stud walls Français Structure de murs en bois Deutsch Holzbalkenwände Español Paredes con montantes de madera Português Paredes de pino de madeira Nederlands Muren met houten balkenconstructie Italiano Pareti con montanti in legno Norsk Vegger med trestendere Dansk Vægge med trædyveler Svenska Väggar med träreglar polski Drewniane ciany szkieletowe Cesky Zdi s devnými výztuhami Türkçe Ahap Profilli Duvarlar / / Deil çelik kullanmak için damizlik duvarlar Olmayan beton kullanimi için beton blok duvarlar Seçeneklerden Birini Belirleyin Yapilmamasi Gerekenler Ne pro pouzití s ocelovou stud stny Ne pro pouzití s konkrétními / betonový blok zdi Vyberte jednu moznost Nedlat Nie stosowa w stalowych cianach stud Nie stosowa z betonu / betonowe ciany bloku Wybra opcj Nie naley: / Ej för användning med stål stud väggar Ej för användning med betong / betong block väggar Välj ett alternativ Gör inte Ikke til brug med stål stud vægge Ikke til brug med beton / betonklods vægge Vælg en mulighed Advarsel Ikke for bruk med stål stud vegger Ikke for bruk med betong / betong blokk vegger Velg et alternativ Forbudt / block Non per l'utilizzo con pareti in acciaio stud Non per l'uso di cemento e pareti a blocchi di cemento Scegliere un'opzione Divieto No para uso con paredes de acero stud Não é para uso com paredes de aço do parafuso prisioneiro Niet voor gebruik met stalen stud wanden Nicht für den Einsatz mit Stahl Ständerwänden Niet voor gebruik met beton / beton blok muren No para uso con hormigón y muros de bloques de hormigón Não é para uso com o concreto / paredes de blocos de concreto Niet voor gebruik met beton / beton blok muren Wählen Sie eine Option Tun Sie Folgendes nicht Ne pas utiliser chez murs à poteaux d'acier Not for use with steel stud walls Not for use with concrete/ concrete block walls Ne pas utiliser avec du béton ou des murs en blocs de béton Choose an Option Do Not WARNING: This product contains small items that could be a choking hazard. Do not use this product for any purpose not explicitly specified by Sanus Systems. The wall must be capable of supporting five times the weight of the TV and mount combined. [. . . ] For TVs with an irregular/obstructed back, see 2-2 or 2-3. If you need extra space to accommodate cables, recesses, or protrusions, see an installation option (2-2 or 2-3) that uses spacers. Ensure that the brackets are level on the back of the TV. CAUTION: Use the shortest screw and spacer combination needed to accommodate cables, recesses, or protrusions. Using hardware that is too long may damage your TV's internal components. Tighten the Lag Bolts only until washer [24] is pulled firmly against the Wall Plate [01]. Any material covering the wall must not exceed 16 mm (5/8 in. Install the arm assembly [03] into the wall plate [01]. the pegs on the top of the arm assembly fit into the slots of the upper sliding car. Be sure to align the bottom holes of the arm assembly with the holes in the lower sliding car. Tighten the tension adjustment [T] to prevent the arms from moving while installing the TV bracket. attach the TV bracket [02] to the arm assembly [03]. There is an audible click when the parts are correctly assembled. Remove the arm covers by pressing the front of the cover; the rear of the cover will pop upward. [. . . ] The information contained in this document is subject to change without notice or obligation of any kind. milestone makes no representation of warranty , expressed or implied , regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. [. . . ]