User manual SANYO AVM-2759S

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. [. . . ] P-Timer . . . . . . . . . . . . . . . . . . . . . . Switches the P-Timer display. Stops P-Timer indication Chapter 7 Controlling the projector Timer setting This page is to set the timer to turn the projector off or on at a programmed day/date and time. Click Timer on the main menu. "---" will appear on the current time when the time is not set up correctly. Present time set on the projector Select date Select day Set execute time Event action How to set the timer 1 Set a day or date To set the timer event at the same time everyday or every week, Select day entry with radio button and then select desired day from the pull-down menu button. The selectable days are as follows: - Same time everyday - Every week (days from Monday to Sunday) To set the timer event on specified date, select date entry with radio button and then type the date with (Year/Month/Date) format. Ex. : Type [2007/12/20] if you specify [December 20, 2007]. This projector does not provide the built-in battery. The date and time information are lost when the projector turns off (when "Eco" is set for the stand-by mode (Refer to p. 74)), or the network configuration is reset. The timer function is disable until time is set up correctly. When using the NTP address for time setting, the current time is acquired at the projector starting up and the timer function is activated after finishing the time setting correctly. Timer setting 2 Set an execute time Type the time with (Hour:Minute) and 24 hours format. Ex. : Type [18:25] if you specify [PM 6 o'clock and 25 minutes]. 3 Select an event action Event Action Select an event action from the pull-down menu. ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Turns on the projector OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Turns off the projector Lamp Auto . . . . . . . . . . . . . . . . . . Click Multi Control on the main menu to display the control page. Note: To control the multiple projectors, each projector must be set the same Network PIN code. Example of multi control PJ1 PJ2 PJ3 PJ4 PC6 PC5 Select Input2 for PJ1 to PJ4. PC4 1 Chapter 7 Controlling the projector Start/stop the multi control To start or stop controlling the multi-projectors, click Multi control setting menu and select ON or OFF. Switches on and off the multi-control function Multi control setting OFF . . . . . . . . . . Stops multi control function ON. . . . . . . . . . . . Starts multi control function. The multi control menu will appear when ON is set. These items of menu are linked to the main menu. The multi controllable menus are "Power & Status", "PC adjustment", "Control", "Setting", "E-mail setting", "Timer", "SNMP setting" and "Network Viewer". Click each menu and perform setting and adjustment. The word "MULTI CONTROL" appears on the each control page while the multi control is operating. This shows the multi control is operating now. Multi-control Register the projector To use the multi control function, register the IP address of the projector you intend to control. Click Pj registration sub menu tab and set the IP address, Memo and Multi control item, then click Set button. Items Description IP address . . . . . . . . . . . . . . . . . Enter IP address of the projector to control Memo. . . . . . . . . . . . . . . . . . . . . . . . . Enter projector name or installed location etc. Multi control item Control . . . . . . . . . . . . . . . . . Controlling the projector Control & Image . . . . . . . . Controlling and displaying images Image. . . . . . . . . . . . . . . . . . . . Displaying the images Confirmation of registered projector To check the registered information, click Check & Change sub menu tab. The registered information of the projector is listed as the below. * The word "none" is displayed if the "Memo" function is used. * When you click on a listed IP address, the login page for the selected projector will be displayed with a new window. IP address Status Memo Page no. Click here to close the sub menu Check & Change. 10 projectors can be registered per page and up to 100 sets can be registered for the multi-control. Chapter 7 Controlling the projector Change the mode of the registered projector To change the mode of the registered projector, select a mode with the pull-down menu button under the IP address of the target projector and then click Set button. Mode Operation Control. . . . . . . . . . . . . . . . . . . . . . . [. . . ] I want to perform the AutoCapture with a commercially available USB memory. To perform AutoCapture, you should have all files and folders of "Auto Capture" folder on `Network Viewer & Capture 5 (CD-ROM)' on the root of USB memory. By copying or drag and dropping those files and folders on the root of a commercially available USB memory, you can perform the AutoCapture as well as a supplied USB memory. CD-ROM > AutoCapture USB thumb drive Auto Capture does not start automatically. Depending on a computer or the security setting of the network, AutoCapture may not start automatically. Please make sure the examples as follows. [. . . ]