User manual SANYO AVM-3680G

[. . . ] * The contents of this manual are subject to change without notice. 2 Contents Chapter 1 Introduction. 10 Microsoft SQL Sever Desktop Engine 2000A installation . 17 Name of the buttons on the tool bar . 18 When the alert occurs on the target or server . [. . . ] Select Encryption Setting from System menu. Select either "On" or "Off " with radio button. Click OK to set the encryption. IP Address setting When the server provides multiple network cards and you want to change the IP address for the PJ Master, or the PJ Master cannot acquire the IP address assigned to the server, use this command to change or acquire the IP address manually. Select IP Address Setting from System menu. Select an IP Address you want to set with the pull-down menu button. and click OK button. * The multiple IP addresses are listed on the pull-down menu button if the server provides multiple network cards. * If "127. 0. 0. 1" appear on the pull-down button, the server may not connect to the network correctly. Make sure that the network cable is connected to the server correctly and the IP address is assigned to the server, and then restart the PJ Master. PJ Master Owner's Manual 27 Chapter 3 Basic operation Customizing the display columns Changing the status column indication 1. Select Column Selection from System menu. On the window, check the column name you want to display on the status list view window . Column Target Name Power Status Lamp Status Input Signal Input Status Input Select Network Status Temperature A Temperature B Temperature C Lamp Time IP Address Model Name Projector Time PJ-Net Ver. PJ Ver. Description Name of the network equipment Status of the network equipment (ON:Normal, OFF:Normal, OFF:P-Mng, Cooling, CountDown, etc. ) Status of lamp (On, Off, Err, LampNonLight, etc. Tick check boxes next to the title name and then click OK to execute the command. After that the targets will operate according to the sending commands. * If there are some errors on the targets or servers, the PJ Master receives error information from the servers or targets and indicates further details on the error log window. See item "Reading of error log" for further information. (p. 36) PJ Master Owner's Manual 31 Chapter 3 Basic operation Default commands for projector TITLE POWER ON POWER OFF VOLUME UP VOLUME DOWN MENU ON MODE MENU OFF MODE DATE SETTING TIME SETTING SCREEN NORMAL SCREEN WIDE BLUE BACK ON BLUE BACK OFF DISPLAY ON DISPLAY OFF LOGO ON LOGO OFF POWER MANAGEMENT ON POWER MANAGEMENT OFF PJ NAME SETTING SMTP SETTING ADMINI ADDRESS SETTING MAIL1 ADDRESS SETTING FANSPEED MAX FANSPPED NORMAL TEXT C00 C01 C09 C0A C1C C1D LF DATE yyyy/mm/dd LF TIME hh:mm CF SCREEN NORMAL CF SCREEN WIDE CF BBACK ON CF BBACK OFF CF DISP ON CF DISP OFF CF LOGO ON CF LOGO OFF CF P-MANE ON CF P-MANE OFF LF PRJNAME PROJECTOR1 LF SMTP 192. 168. 0. 1 LF ADMIN admini@your company name LF MAIL1 user@your company name CF FANSPEED MAX CF FANSPEED NOR Default commands for PDP monitor TITLE POWER ON POWER OFF VOLUME UP VOLUME DOWN MENU ON MODE MENU OFF MODE TEXT C00 C01 C09 C0A C1C C1D * You can define new commands, see item "Customizing the command list" on chapter 4. (p. 46) 32 Global setting Editing the predefined command When changing the command according to the target or resetting date or time to the targets, take the following steps; 1. Select a target on the status list view window or a server on the tree view window. Click or button on the tool bar or select Global Setting from Projector or PDP menu. - The commands which are not effective to the selection are disabled. 3. Double click on a command title name you intend to change. Change command on the text box and click OK to assign the command. Tick check box next to its title name and click OK to execute the command. [. . . ] * To make a new condition check command, click Add to open the edit condition window and enter command and status, and set retry on or off. See item "Condition setting" (p. 28) for further details. The setting window closes. Condition 1 Command: CF STATUS Status:80 Retry: ON Condition 2 Command: CF MODELNM Status:PLC-XF60 Retry: OFF 5-3. The updating command is sent to all the target servers and each server starts updating the firmware of the projectors sequentially. * To check that the firmware of the target was updated successfully, check the version indication on "PJ Ver. " column on the status list view window. [. . . ]