User manual SANYO BC-1206

[. . . ] If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Trouble-shooting" section of the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center. SAFETY PRECAUTIONS WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. G This projector produces intense light from the projection lens. Do not stare directly into the lens as possible. [. . . ] (Refer to page 26, 27. ) G Auto PC Adjustment function cannot be operated in Digital Signal input on DVI terminal and "480p", "575p", "480i", "575i" "720p (HDTV)", "1035i (HDTV)" or "1080i (HDTV)" is selected on PC SYSTEM Menu. 25 COMPUTER INPUT MANUAL PC ADJUSTMENT This projector can automatically tune to display signals from most personal computers currently distributed. However, some computers employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system of this projector. If this happens, projector cannot reproduce a proper image and image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture. This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This enables you to recall setting for a specific computer whenever you use it. Note : This PC ADJUST Menu cannot be operated when in digital signal input on DVI terminal is selected on PC SYSTEM MENU (P24). 1 2 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to PC ADJUST Menu icon. Press POINT UP/DOWN button to move a red frame pointer to item that you want to adjust and then press SELECT button. Press POINT LEFT/RIGHT button to adjust value. Fine sync PC ADJUST MENU PC ADJUST Menu icon Move a red frame icon to item and press SELECT button. Adjusts an image as necessary to eliminate flicker from display. Move a red arrow pointer to Mode that you want to clear and then press SELECT button. Reset Reset all adjust parameters on adjustment dialog box to previous figure. Quit Closes PC ADJUST MENU. Store icon Vacant Mode Shows values of "Total dots, " "Horizontal, " "Vertical, " "Display area H, " and "Display area V. " To clear adjustment data. Mode free icon Close this dialog box. 27 COMPUTER INPUT PICTURE IMAGE SELECT IMAGE LEVEL SELECT (DIRECT) Select image level among Standard, Real, Image 1, Image 2, Image 3 and Image 4 by pressing IMAGE button on Top Control or on Remote Control Unit. Standard Normal picture level preset on this projector. Real Picture level with improved halftone for graphics. IMAGE 1~4 User preset picture adjustment in IMAGE ADJUST Menu (P36). IMAGE button Standard Real Image 1 Image 2 Image 3 Image 4 IMAGE LEVEL SELECT (MENU) 1 2 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to IMAGE SELECT Menu icon. Press POINT UP/DOWN button to move a red frame pointer to level that you want to set and then press SELECT button. Standard IMAGE SELECT MENU IMAGE SELECT Menu icon Move a red frame icon to level and press SELECT button. Level being selected. Normal picture level preset on this projector. [. . . ] (Hz) ON-SCREEN DISPLAY RESOLUTION H-Freq. (Hz) D-VGA D-480p D-575p D-SVGA D-XGA D-SXGA1 640 x 480 720 x 480 (Progressive) 768 x 575 (Progressive) 800 x 600 1024 x 768 1280 x 1024 31. 47 31. 47 31. 25 37. 879 43. 363 63. 98 59. 94 59. 88 50. 00 60. 32 60. 00 60. 02 D-SXGA2 D-720p D-1035i D-1080i D-1080i 1280 x 1024 1280 x 720 (Progressive) 1920 x 1035 (Interlace) 1920 x 1080 (Interlace) 1920 x 1080 (Interlace) 60. 276 45. 00 33. 75 33. 75 28. 125 58. 069 60. 00 60. 00 60. 00 50. 00 NOTE : Specifications are subject to change without notice. 49 APPENDIX MENU TREE Input Input Input 1 RGB RGB( Scart) RGB(PC Digital) RGB( AV HDCP ) Monitor out SYSTEM 1) SYSTEM 1) SYSTEM 2) Input 2 Video Y, Pb/Cb, Pr/Cr RGB SYSTEM 3) SYSTEM 4) SYSTEM 1) SYSTEM 3) SYSTEM 4) SYSTEM 3) Input 3 Video Y, Pb/Cb, Pr/Cr S-Video PC source Screen Video source Normal True Wide System 1) System 2) D-480p Mode 1 Mode 2 VGA 1 SVGA 1 XGA 1 Digital zoom + Digital zoom - System 3) Auto PAL SECAM NTSC NTSC 4. 43 PC adjust Auto PC Adj. Fine sync Total dots Horizontal Vertical 0 - 31 PAL-M PAL-N Image Standard Real Image 1 Image 2 Image 3 Image 4 Current mode Clamp Display area 640 x 480 720 x 400 800 x 600 1024 x 768 1152 x 864 1280 x 1024 1400 x 1050 1600 x 1200 Quit Display area H Display area V Full screen Reset Mode free Store Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Quit Quit On/Off Yes/No System 4) Auto 1080i 1035i 720p 575p 480p 575i 480i Image Standard Cinema Image 1 Image 2 Image 3 Image 4 Screen Normal Wide 50 APPENDIX System Setting Language English German French Italian Spanish Portuguese Dutch Swedish Russian Chinese Korean Japanese Quit Image adjust Contrast Brightness Color Tint Color management Auto picture control Color temp. Red Green Blue Sharpness Gamma Noise reduction Progressive Reset 0 - 63 0 - 63 0 - 63 0 - 63 0 - 63 Off/L1/L2 0 - 63 0 - 63 0 - 63 0 - 31 0 - 15 On/Off Off/L1/L2 Yes/No Image 1 Image 2 Image 3 Image 4 Quit XLow/Low/Mid/High Lamp mode Keystone Aspect V Aspect H Anamorphic Blue back Display Menu position Logo Ceiling Rear Power management On start Remote control code Normal/Auto/Eco Store/Reset Store/Reset Store/Reset On/Off On/Off On/Off On/Off On/Off On/Off Off/Ready/Shut down On/Off Code 1 Code 2 Code 3 Code 4 Code 5 Code 6 Code 7 Code 8 Quit Scale Position Scale Position Store Quit USB Key lock Mouse Projector Off Control panel Remote control Lamp counter reset Factory default Yes/No Yes/No Sound Volume Built-in SP. [. . . ]